24
| English
1 609 929 T86 | (16.12.09)
Bosch Power Tools
Removing the Battery
The battery
3
is equipped with two locking lev-
els that should prevent the battery from falling
out when pushing the battery unlocking button
24
unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by
means of a spring.
To remove the battery
3
, press the battery un-
locking button
24
and pull the battery out of the
power tool toward the rear.
Do not exert any
force.
Battery Charge-control Indication (only for
3.0 Ah battery) (see figure F)
The three green LEDs of the battery charge-con-
trol indicator
32
indicate the charge condition of
the battery
3
. For safety reasons, it is only pos-
sible to check the status of the charge condition
when the machine is at a standstill.
Press button
31
to indicate the charge condi-
tion. This is also possible when the battery
3
is
removed.
When no LED lights up after pushing button
31
,
then the battery is defective and must be re-
placed.
Mounting/Replacing the Saw Blade
f
Before any work on the power tool, remove
the battery.
f
When mounting the saw blade, wear protec-
tive gloves.
Danger of injury when touching
the saw blade.
f
Only use saw blades that correspond with
the characteristic data given in the operat-
ing instructions.
f
Do not under any circumstances use grind-
ing discs as the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can
be found at the end of this manual.
Removal of the Saw Blade (see figure A)
For changing the cutting tool, it is best to place
the machine on the face side of the motor hous-
ing.
– Press the spindle lock button
14
and keep it
pressed.
f
The spindle lock button 14 may be actuated
only when the saw spindle is at a standstill.
Otherwise, the power tool can be damaged.
– With the Allen key
16
, unscrew the clamping
bolt
22
turning in rotation direction
n
.
– Tilt back the retracting blade guard
7
and
hold firmly.
– Remove the clamping flange
21
and the saw
blade
20
from the saw spindle
18
.
Mounting the Saw Blade (see figure A)
For changing the cutting tool, it is best to place
the machine on the face side of the motor hous-
ing.
– Clean the saw blade
20
and all clamping
parts to be assembled.
– Tilt back the retracting blade guard
7
and
hold firmly.
– Place the saw blade
20
onto the mounting
flange
19
. The cutting direction of the teeth
(direction of arrow on the saw blade) and the
direction-of-rotation arrow on the retracting
blade guard
7
must correspond.
– Mount the clamping flange
21
and screw in
the clamping bolt
22
turning in rotation di-
rection
o
. Observe correct mounting posi-
tion of mounting flange
19
and clamping
flange
21
.
– Press the spindle lock button
14
and keep it
pressed.
– Tighten the clamping bolt
16
with the Allen
key
22
by turning in rotation direction
o
. The
tightening torque is 6–9 Nm, which corre-
sponds to hand tight plus ¼ turn or
3 graduation marks of the marks
23
on the
blade guard
4
.
LED
Capacity
Continuous lighting 3 x green
≥
2/3
Continuous lighting 2 x green
≥
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
OBJ_BUCH-755-003.book Page 24 Wednesday, December 16, 2009 9:18 AM
