English– 15
1 609 929 F67 • (04.10) PS
Checking and Adjusting Basic Adjustment
Before all work on the machine, pull the mains
plug.
To ensure precise cuts, the basic adjustment must be
checked and adjusted as necessary after intensive us#
age.
Bevel Angle 0° (Vertical)
Place the electro#tool in the transport position.
Rotate the saw table
18
to the detent
17
for 0°. The le#
ver
15
must audibly engage in the detent.
Checking:
(see Figure
)
Place a combination square set to 90° on the saw ta#
ble
18
. The leg of the square must be flush with the
saw blade over its entire length.
Adjusting:
(see Figure
)
Loosen the clamping handle
16
. Loosen the bolts
60
and
61
with the open#ended spanner
3
(SW 10) pro#
vided. Loosen th e adjustment screw
62
(approx. 3
turns) with the socket spanner
35
(SW 4) provided.
Screw the adjustment bolt
59
(SW 10) in or out far
enough until the leg of the protractor is flush with the
saw blade over its entire length.
Retighten the clamping handle
16
. Retighten first the
adjustment screw
62
and then the bolt
60
and
61
.
In case the angle indicators
24
and
33
are not in a line
with the 0° mark of the scale
32
after the adjustment,
loosen the attachment screws of the angle indicators
with the Phillips screwdriver
35
provided and align the
angle indicators along the 0° mark.
Left Bevel Angle 45° (Vertical)
Place the machine in the working position.
Rotate the saw table
18
to the notch
17
for 0°. Loosen
the clamping handle
16
. Swing the tool arm with the
handle
7
to the left to the tool arm stop.
Checking:
(see Figure
)
Set the combination square to 45° and place it on the
saw table
18
. The leg of the square must be flush with
the saw blade over its entire length.
Adjusting:
(see Figure
)
Screw the adjustment bolt
63
(SW 10) in or out far
enough so that the leg of the protractor is flush with the
saw blade over its entire length.
Retighten the clamping handle
16
.
In case the angle indicators
24
and
33
are not in a line
with the 45° mark on the scale
32
after the adjustment,
first recheck the 0° adjustments for the bevel angle
and the angle indicator. Then repeat the adjustment
for the 45° bevel angle.
Clamping Action of the Clamping Handle for
the Vertical Bevel Angle
(also see Figure
)
Loosen the clamping handle
16
.
Adjusting:
Turn the adjustment bolt
64
with th e open#ended
spanner
3
(SW 17) counter#clockwise to reduce th e
clamping action or clockwise to increase the clamping
action.
Set a vertical bevel angle, tighten the clamping handle
16
and ch eck if th e desired clamping action is
achieved.
The clamping force must securely hold the tool arm in
any vertical bevel angle position.
Clamping Action of the Handle Clamp
(see Figure
)
Open the clamp
5
.
Adjusting:
Turn the adjustment screws
65
with th e Allen key
2
(SW 1.5) counter#clockwise to reduce the clamping
action or clockwise to increase the clamping action.
Always adjust the two screws to the same height.
Close the clamp
5
and check whether the desired
clamping action is achieved.
Angle Indicator (Horizontal)
(see Figure
)
Place the machine in the working position.
Rotate the saw table
18
to the detent
17
for 0°.
Checking:
The angle indicator
66
must be in alignment with the
0° mark of the scale
40
.
Adjusting:
Loosen the attachment screw of the angle indicator
with the Phillips screwdriver
35
provided and align the
angle indicator along the 0° mark.
Retighten the attachment screw.
V1
V2
W1
W2
W2
X
Y
Summary of Contents for GCM 12 SD
