English |
19
Bosch Power Tools
1 609 92A 0JA | (22.6.15)
Removing the Key Type Drill Chuck
– Push the locking sleeve
5
toward the rear and pull out the
key type drill chuck
23
.
Removing/Inserting the Quick Change Chuck
(GBH 36 VF-LI Plus)
The SDS-plus quick change chuck
2
can easily be replaced
against the quick change keyless chuck
1
provided.
Removing the Quick Change Chuck (see figure D)
– Pull the lock ring for the quick change chuck
6
toward the
rear, hold it in this position and pull off the SDS-plus quick
change chuck
2
or the quick change keyless chuck
1
to-
ward the front.
– After removing, protect the replacement chuck against
contamination.
Inserting the Quick Change Chuck (see figure E)
Use only model-specific original equipment and pay at-
tention to the number of identification grooves 26.On-
ly quick-change chucks with two or three identification
grooves are permitted.
When an unsuitable quick-change
chuck is used, the application tool could fall out during op-
eration.
– Before inserting, clean the quick change chuck and apply a
light coat of grease to the shank end.
– Grasp the SDS-plus quick change chuck
2
or the quick
change keyless chuck
1
completely with your hand. Slide
the quick change chuck with a turning motion onto the drill
chuck mounting
25
until a distinct latching noise is heard.
– The quick change chuck is automatically locked. Check the
locking effect by pulling the quick change chuck.
Changing the Tool
The dust protection cap
4
largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
tool, take care that the dust protection cap
4
is not damaged.
A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Changing the Tool (SDS-plus)
Inserting SDS-plus Drilling Tools (see figure F)
The SDS-plus drill chuck allows for simple and convenient
changing of drilling tools without the use of additional tools.
– GBH 36 VF-LI Plus: Insert the SDS-plus quick change
chuck
2
.
– Clean and lightly grease the shank end of the tool.
– Insert the tool in a twisting manner into the tool holder until
it latches itself.
– Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus drilling tool can
move freely. This causes a certain radial run-out at no-load,
which has no effect on the accuracy of the drill hole, as the
drill bit centres itself upon drilling.
Removing SDS-plus Drilling Tools (see figure G)
– Push back the locking sleeve
5
and remove the tool.
Changing the Tool (without SDS-plus)
(GBH 36 V-LI Plus)
Inserting (see figure H)
Note:
Do not use tools without SDS-plus for hammer drilling
or chiselling! Tools without SDS-plus and their drill chucks are
damaged by hammer drilling or chiselling.
– Insert a key type drill chuck
23
(see “Inserting/Removing
the Key Type Drill Chuck”, page 18).
– Open the key type drill chuck
23
by turning until the tool
can be inserted. Insert the tool.
– Insert the chuck key into the corresponding holes of the
key type drill chuck
23
and clamp the tool uniformly.
– Turn the mode selector switch
13
to the “drilling” position.
Removing (see figure I)
– Turn the sleeve of the key type drill chuck
23
with the drill
chuck key in anticlockwise direction until the drilling tool
can be removed.
Changing the Tool (without SDS-plus)
(GBH 36 VF-LI Plus)
Inserting (see figure J)
Note:
Do not use tools without SDS-plus for hammer drilling
or chiselling! Tools without SDS-plus and their drill chucks are
damaged by hammer drilling or chiselling.
– Insert the quick change keyless chuck
1
.
– Firmly hold the retaining ring
29
of the quick change
chuck. Open the tool holder by turning the front sleeve
28
until the tool can be inserted. Tightly hold the retaining ring
29
and firmly turn the front sleeve
28
in the direction of the
arrow until a distinct latching noise can be heard.
– Check the tight seating by pulling the tool.
Note:
If the tool holder was opened to the stop, then the latch-
ing noise possibly may be heard while closing the tool holder
and the tool holder will not close.
In this case, turn the front sleeve
28
once in the opposite di-
rection of the arrow. Afterwards, the tool holder can be
closed (tightened) again.
– Turn the mode selector switch
13
to the “drilling” position.
Removing (see figure K)
– Firmly hold the retaining ring
29
of the quick change
chuck. Open the tool holder by turning the front sleeve
28
in the direction of the arrow until the tool can be removed.
Dust Extraction with GDE 16 Plus (Accessory)
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
OBJ_BUCH-283-012.book Page 19 Monday, June 22, 2015 10:28 AM
