background image

Introduction | 2

Bosch Motorsport

e-GoKart_Powertrain__Young_Star__Manual

5 / 60

2.1.2 Safety and Warning Notes

To avoid the risk of an electric shock, which can lead to death or serious injury, any short

circuit of the interfaces (poles) of the Energy Storages ES 5-2.4, e.g. by tool drop, shall be

avoided.

2.1.3 Conditions for Transport and Storage

Storage of the product between shipment from BOSCH MOTORSPORT plant and mount-

ing/initial operation at the CUSTOMER shall be realized in defined transport packaging.

# Deliverables shall be handled with care.

If possible, all BOSCH MOTORSPORT e-GoKart System components are shipped as com-

plete units packed securely in appropriate transportation devices to protect the compon-

ents from damage or corrosion (protection against dust, moisture, precipitation, solar irra-

diation, etc.) that may result from usual transportation conditions.

# The CUSTOMER shall inform BOSCH MOTORSPORT if irregular / special transportation

conditions may occur having an impact on usual transportation devices applied.

# During storage of unpacked components at CUSTOMER site the CUSTOMER shall en-

sure that products are protected against damage or corrosion.

# Deliverables shall be stored for maximum 1 year.

# Deliverables shall only be transported or stored with an environment temperature

<80°C.

If above conditions are not fulfilled, the intended application is only allowed after inspec-

tion and agreement by BOSCH MOTORSPORT. Related expenses have to be compensated

by the CUSTOMER.

# Deliverables shall not be stored in humid/moist conditions (especially in case of oversea

transportation) and shall never be exposed to extreme heat or fire nor corrosive sub-

stances. This applies to installed and uninstalled units as well as packed and unpacked

units. If components are strongly subjected to water (e.g. due to transportation, applica-

tion of a cleaning process), a drying process shall be performed before storing those.

# Deliverables are not allowed to fall or be subjected to uncommon stresses (temperature,

acceleration, ultraviolet rays, etc.). In these circumstances further use of the deliverables is

not permitted.

# During storage, all external electrical connections from the application input/output in-

terfaces and the power connector shall be removed and connector inserts, where sup-

plied, fitted.

# During storage or transport of the unpacked BOSCH MOTORSPORT e-GoKart System

electrostatic charging and discharging of unpacked Energy Storages ES 5-2.4 shall be

avoided.

# There shall never be placed any heavy objects on unpacked deliverables (especially the

48 V Energy Storages ES 5-2.4) or the inter-connecting cables.

# The Power Unit 5-10 shall be transported or stored horizontally.

# Axial loads or shocks on the rotor shaft of the unpacked e-GoKart Drive unit are not

permitted. This may result in pre-damage of bearings. This applies also to operation.

# The Power Unit 5-10 is not allowed to fall or be subjected to uncommon stresses (tem-

perature, acceleration, ultraviolet rays, etc.). Under these circumstances, further use of the

e-GoKart Drive unit is not permitted.

Summary of Contents for e-GoKart PowerTrain Young Star





























































Reviews: