background image

en

    Operating the appliance

6

Control panel model 2

Control panel

Setting the fan

Switching on the appliance

Press the 

%

 button.

The fan starts at setting 

ƒ

.

Press the + or - button to change the fan strength.

Switching off

Press the 

%

 button.

Intensive setting

You can use the intensive setting if there is a large 

build-up of odours and fumes/vapours.
Press the + button when the fan is at setting 

.

The intensive boost setting

 is activated. Pressing the + 

button again activates the intensive boost 

ƒ

setting.

After approx. six minutes, the electronics automatically 

reduce the fan to a lower setting . If you want to end the 

intensive setting before the preset time expires, press 

the - button until the required fan setting is reached.

Fan run-on time

The fan run-on time is possible at every fan setting 

(except boost

 and boost 

ƒ

).

Select the desired fan setting and press the 

r

 button. 

Š

min

r

 appears on the display.

Once this time has elapsed, the fan switches off 

automatically.

Setting the run-on time

When 

Š

min

 appears on the display, press the + or - 

button.
You can set a run-on time of between 1 and 9 minutes.

Lighting

The lighting can be switched on and off independently 

of the fan.
Press the 

B

 button.

Setting the brightness

Press and hold the 

B

 button until the desired 

brightness is reached.

Saturation display

When the metal mesh grease filters or the activated 

carbon filter are saturated, a signal sounds for approx. 

4 seconds after the fan is switched off.
In addition, the corresponding symbol appears in the 

display:  

Metal mesh grease filter:

 #

Activated carbon filter: 

#

If you have not yet done so, the metal mesh grease 

filters should be cleaned or the activated carbon filter 

changed now. 
For instructions on how to clean the metal mesh grease 

filters, please refer to the section 

Cleaning and 

maintenance

.

While the saturation displays are flashing, they can be 

reset. To do this, press the 

#

 button.

Switching over the display for circulating-air mode

For circulating-air mode, the electronic control display 

must be switched over accordingly:

The extractor hood must be connected and switched 

off.

Press the 

%

 and 

r

 buttons at the same time until 

the

display for starter sets for circulating-air mode or

#

 display for CleanAir circulating air modules

lights up.

Repeatedly press the button combination to switch 

the electronic control display back to exhaust air 

mode (

#

 display).

Audible signal 

Switching on the acoustic signal

When the fan is switched off, press the 

 and + 

buttons at the same time for approx. three seconds. An 

acknowledgement signal sounds.

Switching off the acoustic signal

Repeat the "Switching on the acoustic signal" process.

Explanation

%

Fan on/off

#

Switch off the saturation display

 -

Reduce the fan settings

 +

Increase the fan settings/intensive setting 1, 2

r

Fan run-on time

B

 Light on/off/dimming

ERRVW

Summary of Contents for DWA097E51A

















Reviews: