manualshive.com logo in svg

Bosch DS6R2, Installation And Operation Manual

Share
Download
Bosch DS6R2 Installation And Operation Manual Download Page 6

DS6R2 

|

 

Installation and Operation Guide | 2.0 Installation 

 

 

6 

Bosch Security Systems, Inc. | 4/08 | F01U081960-01

 

2.0

 

Installation 

 

Install the DS6R2 as described in this 
document to avoid damage to the devices. 

When installation is complete, perform a 
full system test. 

 

2.1

 

Mounting the DS6R2 

You can mount the DS6R2 directly to the intended 
surface (flush or semi-flush), or you can mount it to an 
electrical box. 
1.

 

To open the keypad, use a screwdriver to press the 
release tabs on the bottom of the keypad. 
Refer to 

Figure 2

. 

 

Figure 2: Opening the DS6R2 

1

1

 

1- Release tab 

 

2.

 

Mount the base on the intended surface or 
electrical box. 
Refer to 

Figure 3

. 

 

Figure 3: Mounting Holes 

1

1

2

2

3

 

1-  Holes for surface-mounting 

2-  Holes for electrical box 

3-  Hole for wall tamper screw 

 

 

To use the wall tamper feature, mount the 
DS6R2 directly to the intended surface. 

 

 

2.2

 

Wiring the DS6R2 

2.2.1.

 

System Wiring 

 

Remove power to all devices before 
connecting or removing the DS6R2. 

 

Connect devices as shown in 

Figure 4

. If the DS6R2 is 

the last device on the RS-485 bus, connect a 120 

Ω

 

EOL resistor in parallel with the  
RS-485 bus. 

 

Only the last device on the RS-485 bus 
requires a 120 

Ω

 EOL resistor (included 

with the MTGW CAN-RS-485 BUS 
Gateway). 

 

 

Figure 4: RS-485 Bus Wiring 

DS6R

MT1-8

MT1-1

MTGW

RS-485

 1

1

 

1- 120 

Ω

 EOL resistor 

 

Summary of Contents for DS6R2



















Reviews:

No comments

Brands by name

Popular brands

Load more brands