Bosch DIP-7180-00N Installation Manual Download

Page: 15 / 52

DIVAR IP 7000 (2U)

System overview | en

Bosch Sicherheitssysteme GmbH

Installation Manual

2016.07 | V2 | DOC

Rear view:

2x power supply modules

2x redundant SSD drives for operating
system (RAID1 mirror)

1x serial port

1x network port for BMC (Baseboard
Management Controller) connection
and IPMI (Intelligent Platform
Management Interface) monitoring

4 USB ports

2x network ports for data transmission
(teamed)

Note:

Do not change the teaming

mode!

1x VGA display output (do not use!)

1x graphic card (4x mini display port)

Note:

Provides digital signal. An active

adapter is required to connect analog
monitors.

1x sound card (audio inputs and
outputs)

3.3.1

Control panel buttons

There are two push-buttons located on the front of the chassis. These are (in order from left
to right) a reset button and a power on/off button.

–

Reset

: The reset button is used to reboot the system.

–

Power:

The main power switch is used to apply or remove power from the power

supply to the system. Turning off system power with this button removes the main power
but keeps standby power supplied to the system.

Therefore, you must unplug system

before servicing.

3.3.2

Control panel LEDs

The control panel located on the front of the chassis has LEDs to provide you with critical
information related to different parts of the system. This section explains what each LED
indicates when illuminated.

Summary of Contents for DIP-7180-00N





















































Search results

Summary of Contents for DIP-7180-00N

Reviews:

Related manuals for DIP-7180-00N

Brands by name

Popular brands

Bosch DIP-7180-00N, Installation Manual

Search results

Summary of Contents for DIP-7180-00N

Reviews:

Related manuals for DIP-7180-00N

Brands by name

Popular brands