manualshive.com logo in svg

Bosch D8125, Operation And Installation Manual

Share
Download
Bosch D8125 Operation And Installation Manual Download Page 37

D8125

D8125 Operation and Installation Guide

Page 37

© 2004 Bosch Security Systems, Inc.

74-04247-000-N

Installation

If six POPITs are assigned in programming to each of five master zones, and one POPIT has erroneous switch settings (see
Figure 16), Master Zone 5 appears to have only five POPITs installed, and Master Zone 7 (which has no POPITs assigned in
programming) appears to have one POPIT installed. Both “missing” and “extra” POPIT conditions will be displayed on the
D1252A.

2.5   Z1POINTS      6

2.12 Z8POINTS     00

PROGRAMMED

2.6   Z2POINTS      6

2.7   Z3POINTS      6

2.8   Z4POINTS      6

2.9   Z5POINTS      6

2.10 Z6POINTS     00

2.11 Z7POINTS     00

MASTER ZONE 1:  6

MASTER ZONE 2:  6

MASTER ZONE 3:  6

MASTER ZONE 4:  6

MASTER ZONE 5:  5

MISSING
POPIT

MASTER ZONE 7:  1

EXTRA
POPIT

INSTALLED

Figure 16: POPIT Switch Setting Error

Figure 17 also displays a system containing one POPIT with erroneous switch settings. Both “missing” and “extra” POPIT
conditions will be displayed on the D1252A after entering a [Command 44].

2.5   Z1POINTS      6

2.12 Z8POINTS     00

PROGRAMMED

2.6   Z2POINTS      6

2.7   Z3POINTS      6

2.8   Z4POINTS      6

2.9   Z5POINTS      6

2.10 Z6POINTS     00

2.11 Z7POINTS     00

MASTER ZONE 1:  6

MASTER ZONE 2:  6

MASTER ZONE 3:  6

MASTER ZONE 4:  5

MASTER ZONE 5:  7

MISSING
POPIT

EXTRA
POPIT

INSTALLED

Figure 17: POPIT Switch Setting Error

Summary of Contents for D8125

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands