Bosch CS 550 Installation Manual Download Page 11 | Manualshive

Page: 11 / 20

background image

11/20

Bosch Rexroth Canada ı

May 2019

ı Revision

5.0

7 Cable Connections

7.1

Cable Connections

Connect the CANBUS EXTENSION from CAN1 to the CANBUS lead on the main harness

or to the FEMALE CONNECTOR on the armrest (if equipped).

Connect the MALE CONNECTOR to CAN2 of the RCE harness.

If switches are present: Connect the power harness to the ignition, disconnect then to the 2

PIN CONNECTOR.

•

P3 interconnects with the 16 PIN ARMREST CONNECTOR. Connect the power

harness to battery or ignition disconnect.

•

P5 is for the AUXILIARY CABLE with bare leads. (See OSD for pinouts.)

«
...
9
10
11
12
13
...
»

Summary of Contents for CS 550





















Reviews:

No comments

Related manuals for CS 550

Brand: Faber Pages: 8

Brand: OmarLift Pages: 14

Brand: Raymarine Pages: 12

Brand: Jafar Pages: 13

Brand: Warren Controls Pages: 16

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: JENCO Pages: 36

Brand: jcm-tech Pages: 8

Brand: Rain Bird Pages: 20

Brand: M-system Pages: 10

M-DUINO PLUS series

Brand: Industrial Shields Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands