Bosch BGH96 Series Installation, Operation And Maintenance Manual Download

Page: 50 / 56

5 0 |

Bosch 96% AFUE Gas Furnace

Installation, Operation & Maintenance

04.2019

Bosch Thermotechnology Corp.

Data subject to change

Symptoms of
Abnormal
Operation

Associated

LED

Fault Description(s)

Possible Reason

Corrective Action

Cautions And Notes

Furnace fails
to operate

NONE

—

No 115 volt

power to

furnace, or no

24 volt power to

integrated control

module

—

Blown fuse or

circuit breaker

—

Integrated control

module has an

internal fault

—

Door switch open, or 24 volt

wires improperly connected or

loose.

—

Blown fuse or circuit breaker

—

Integrated control module has

an internal fault

1. Assure 115 and 24 volt power to

furnace's integrated control module.

2. Check integrated control module's

fuse (3A). Replace if necessary.

3. Check for possible shorts in 115 and

24 volt circuits. Repair as necessary

OR replace bad integrated control

module.

—

Turn power OFF prior to repair.

—

Replace integrated control

module's fuse with 3A

automotive fuse.

—

Read precautions in

Electrostatic Discharge

section of manual.

RED

Furnace fails
to operate

1 FLASH

—

Flame sensed

with gas valve off

—

Short to ground in flame sense

circuit.

1. Correct short at ﬂ ame sensor or in

ﬂ ame sensor wiring

—

Turn power OFF prior to repair.

Furnace fails
to operate

2 FLASH

—

Pressure switch

closed with

inducer off

—

Induced draft blower pressure

switch contacts "stuck".

—

Shorts in pressure switch circuit.

1. Replace induced draft blower's

pressure switch.

2. Repair

short.

—

Turn power OFF prior to repair.

—

Replace pressure switch with

proper replacement part.

Induced draft
blower runs
continuously
with no
further
furnace
operation.

3 FLASH

6 FLASH

13 FLASH

—

Low fire pressure

switch open with

inducer on

—

Pressure switch

cycle lockout

—

High fire pressure

switch open with

high inducer on

—

Pressure switch hose blocked,

pinched or connected

improperly, blocked flue, or

weak induced draft blower.

—

Incorrect pressure switch

setpoint or malfunctioning

switch contacts.

—

Loose or improperly connected

wiring.

1. Inspect pressure switch hose.

Repair if necessary. Inspect ﬂ ue for

blockage, proper length, elbows, and

termination.

2. Replace pressure switch.

3. Tighten or correct wiring connection.

—

Turn power OFF prior to repair.

—

Replace pressure switch with

proper replacement part.

Furnace fails
to operate.

4 FLASH

5 FLASH

11 FLASH

—

Limit/RoIIout

switch open less

than 5 mins

—

Limit/RoIIout

switch open more

than 15 mins

—

Limit/RoIIout

switch open from

5 to 15 mins

—

Faulty chamber limit switch or

fan mounted limit switch.

—

Insufficient conditioned air over

the heat exchanger. Blocked

filters, restrictive ductwork,

improper circulator blower

speed or failed circulator

blower

—

Misaligned burners, blocked

flue, or failed induced draft

blower.

—

Faulty rollout switch - resettable.

—

Faulty inducer.

—

Loose or improperly connected

wiring.

1. Check chamber limit switch or fan

mounted limit switch. Replace if

necessary.

2. Check ﬁ lters and ductwork for

blockage. Clean ﬁ lters or remove

obstruction. Check circulator blower

speed and performance. Correct

speed or replace blower if necessary.

3. Check burners for proper alignment.

Check ﬂ ue and air inlet piping for

blockage, proper length, elbows and

termination. Correct as necessary.

4. Check rollout switch - resettable.

Replace if necessary.

5. Check induced draft blower for proper

performance. Replace if necessary.

6. Tighten or correct wiring connection.

—

Turn power OFF prior to repair.

—

Replace pressure switch with

proper replacement part.

Table 25

Troubleshooting Chart

Summary of Contents for BGH96 Series

























































Search results

Summary of Contents for BGH96 Series

Reviews:

Related manuals for BGH96 Series

Brands by name

Popular brands

Bosch BGH96 Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for BGH96 Series

Reviews:

Related manuals for BGH96 Series

Brands by name

Popular brands