Bosch AutoDome, Mounting Manual

Page: 8 / 24

2 UNPACKING
Unpack carefully. This equipment should be handled with
care to prevent damage.
Check for the following items and part numbers:
*Kits with AutoTracker end in “T”.
Kits with Surge Protection end in “SP”.
ENV-PAO ships with only the two (2) Rubber Hole Plugs. All
other kits ship with the parts listed below.
Bag of Parts:
The following items are shipped in a separate bag:
ν
One (1) 3-pin power connector.
ν
Two (2) Rubber hole plugs.
ν
One (1) Green ground screw.
ν
One (1) Ring terminal for ground wire.
ν
One (1) 3-pin alarm connector (AutoTracker only).
ν
One (1) 6-pin signal connector (Not included with fiber
units).
If any items appear to have been damaged in shipment,
replace the item(s) properly in the shipping carton and notify
the shipping company. If any items are missing, notify your
Bosch Sales Representative or Customer Service
Representative.
Service Centers
U.S.A.: Phone: 800-366-2283 or 408-956-3895
fax: 800-366-1329 or 408-956-3896
e-mail: NationalServiceCenter@ca.slr.com
Canada: 514-738-2434
Europe, Middle East & Asia Pacific Region:
32-1-440-0711
For additional information,
see www.boschsecuritysystems.com.
NOTE:
The shipping carton and all packing materials should
be retained, in case transporting the unit is necessary. This will
ensure safe transport of all components.
3 TOOLS REQUIRED
ν
Standard screwdriver
ν
5 ⁄
16
-inch wrench or socket
ν
16 mm wrench or socket (if using metric fasteners)
ν
3 ⁄
8
-inch wrench or socket
ν
Other tools as needed for preparing the mounting
surface
ν
**Banding Tool, Part # TC9311PM3T (Sold separately. Must
be purchased if installing Mast Mount Kit.)
4 INSTALLATION
4.1 Rough Wiring
If wiring a 24V version, refer to the chart in APPENDIX A for
maximum distances from transformer to dome.
4.1.1. If wiring the pendant arm box through the bottom
instead of the back, use the plugs supplied with the box
unit to close the holes in the back of the mounting
plate (as shown in PHOTO 4A).
Photo 4A
4.1.2. Use only liquid-tight fittings or liquid-tight conduit fit-
tings in the two (2) holes in the back of the back/wall
mounting plate
(as shown in PHOTO 4B), or bottom of
the pendant arm box . When using liquid tight fittings, it
is important to use the appropriate cable width for a
snug fit. If a snug fit is not possible, any liquid tight
3 ⁄
4
-inch
conduit fitting with a gasket and locking nut may be used
instead.
Installation EN
© 2003 Bosch Security Systems Page 8 of 24
APPLICABLE PRODUCT PART# *
Wall Mount Kit:
Arm with box and . . .
• NO Transformer ENV-PA0
• Transformer -
120 VAC / 230 VAC ENV-PA1 / ENV-PA2
• Transformer w/Fiber Optic
Module - 120 VAC / 230 VAC ENV-PA1F / ENV-PA2F
Bag of Parts (See below)
Corner Mount Kit:
Arm with box and . . .
• NO Transformer ENV-PA0
• Transformer -
120 VAC / 230 VAC ENV-PA1 / ENV-PA2
• Transformer w/Fiber Optic
Module - 120 VAC / 230 VAC ENV-PA1 / ENV-PA2F
Corner Plate LTC 9542/01
Bag of Parts (See below)
Mast** Mount Kit:
Arm with box and . . .
• NO Transformer ENV-PA0
• Transformer -
120 VAC / 230 VAC ENV-PA1 / ENV-PA2
• Transformer w/Fiber Optic
Module -120 VAC / 230 VAC ENV-PA1 / ENV-PA2F
Mast Kit LTC 9541/01
Bag of Parts (See below)