English |
17
Bosch Power Tools
1 609 92A 3FK | (15.12.16)
Mounting VAC Accessories
The vacuum hose
16
is equipped with a clip system, with
which the VAC accessories (extraction adapter
17
, curved
nozzle
18
) can be connected.
Fitting the extraction adapter or curved nozzle
(see figure B)
– Fit the extraction adapter
17
or the curved nozzle
18
to the
vacuum hose
16
until the two snap fasteners
27
of the vac-
uum hose click into place.
– To disassemble, press both snap-fasteners
27
inward and
pull the components apart.
Mounting Nozzles and Tubes
– Then attach the required vacuuming accessory (floor noz-
zle, crevice nozzle, suction tube, etc.) firmly to the curved
nozzle
18
or the extraction adapter
17
.
Replacing/Inserting the Dust Bag
(Dry Vacuuming) (see figures C1–C2)
You can use a dust bag (accessory) for dry vacuuming. This
makes the dust easier to dispose of.
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches
8
and remove the vacuum lid
7
.
– Pull the full dust bag
29
backwards out of the connection
flange
28
and remove it from the vacuum cleaner.
– Work the new dust bag over the connection flange of the
vacuum cleaner. Make sure that the dust bag faces com-
pletely against the interior sides of the container
1
over its
full length.
– Reattach the vacuum lid
7
again and lock the latches
8
.
Changing inserts for the floor nozzle
(see figures D1 – D2)
Depending on the vacuuming work to be carried out (dry, wet,
carpet, etc.), you can clip different inserts into the floor noz-
zle
21
(e.g. rubber lip, brush insert).
– Press the release buttons
30
on the floor nozzle
21
to re-
lease the insert from the floor nozzle.
– Clip the required insert
22
/
23
/
24
into the floor nozzle
21
.
Operation
Before any work on the vacuum cleaner itself, pull the
mains plug.
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the vacuum cleaner. Equipment marked
with 230 V can also be operated with 220 V.
Only use an undamaged filter (no cracks, small holes,
etc.). Replace a damaged filter immediately.
The vacuum cleaner may generally not be used in rooms
where the danger of an explosion exists.
To save energy, only switch the vacuum cleaner on when us-
ing it.
To ensure optimal vacuuming performance, always complete-
ly unwind the vacuum hose
16
from the vacuum cleaner lid
7
.
Dry Vacuuming
Vacuuming of deposited dust
UniversalVac 15
:
AdvancedVac 20
:
Extraction of dust resulting from running power tools
(see figure E)
– Fit the extraction adapter
17
(see “Fitting the extraction
adapter or curved nozzle”, page 17).
– Insert the extraction adapter
17
into the dust extraction
outlet for the power tool.
Note:
When working with power tools that have a low air feed
into the vacuum hose (e.g. jigsaws, sanders, etc.), the air dif-
fuser
31
of the vacuum hose
16
must be opened. This will im-
prove the total output of the vacuum cleaner and the power
tool.
To do so, turn the ring above the air diffuser
31
until the max-
imum opening is produced.
AdvancedVac 20
:
A socket outlet with earthing contact
4
is integrated in the
vacuum cleaner. An external power tool can be connected
there. Observe the maximal allowable load of the connected
power tool.
– To
start the operation
of the vac, switch on the power tool
connected to the socket
4
. The vacuum cleaner starts au-
tomatically.
– Switch the power tool off to
end
the
vacuuming
.
The delayed action shutdown of the Automatic Start/Stop
continues to run for up to 6 seconds in order to extract re-
sidual dust from the vacuum hose.
Wet Vacuuming
CAUTION! This appliance is not suitable for picking up
hazardous dust. Do not vacuum inflammable or explo-
sive fluids; for example, benzene, oil, alcohol, solvents.
Do not vacuum hot or burning dust. Do not operate the
machine in rooms where the danger of an explosion ex-
ists.
The dusts, vapours or fluids can ignite or explode.
The vacuum cleaner may not be used as a water pump.
The vacuum cleaner is intended for vacuuming air and wa-
ter mixtures.
– To
switch on
the vacuum cleaner, set the
on/off switch
5
to the “Vacuuming” symbol.
– To
switch off
the vacuum cleaner, set the
On/Off switch
5
to the “Switching Off” sym-
bol.
– To
switch on
the vacuum cleaner, set the
mode selector switch
5
to the “Vacuuming”
symbol.
– To
switch off
the vacuum cleaner, set the
mode selector switch
5
to the “Off” symbol.
– To
activate the automatic
start/stop
of the vacuum cleaner, set
the mode selector switch
5
to the
“Automatic Start/Stop” symbol.
– To
switch off
the vacuum cleaner, set the
mode selector switch
5
to the “Off” symbol.
OBJ_BUCH-3012-002.book Page 17 Thursday, December 15, 2016 9:29 AM
