Bosch ACS 511 Repair Instruction Download

Page: 13 / 40

1 689 975 252

2019-05-15

Robert Bosch GmbH

Service phases | ACS 511 | 13

8.2

Draining oil into the used oil bottle

At the end of recovery, the solenoid valve EV7 opens
and the oil previously separated out in the evaporator/
oil separator (4) drains into the used oil bottle (9).

The used oil bottle scales (13) weigh the drained used
oil and ACS 511 saves the value for fresh oil filling in
automatic mode.

EV5

EV3

EV6

VU2

EV7

EV10

HIGH

LOW

EV1

VU3

VU1

EV8

EV9

active

Name

Description

Fresh oil tank

Vacuum pump

Expansion valve

Evaporator/oil separator

Compressor oil separator

Compressor

Internal refrigerant cylinder

Refrigerant cylinder scales

Used oil bottle

Heat exchanger

UV dye bottle

Fresh oil scales

Used oil scales

EV1

Vacuum solenoid valve

EV3

Flow solenoid valve

Name

Description

EV5

Recovery solenoid valve

EV6

Filling solenoid valve

EV7

Oil drain solenoid valve

EV8

Oil injection solenoid valve

EV9

Contrast medium injection sole-

noid valve

EV10

Solenoid valve for separating

high and low pressure

Coarse filter

Combi filter

High pressure

Low pressure

Low pressure gage

High pressure gage

Internal refrigerant cylinder pres-

sure gage

Name

Description

Pressure sensor

Pressure switch

Low pressure hose

High pressure hose

Tank vapour side hose valve

Tank liquid side hose valve

Tank vapour side valve

Tank liquid side valve

Safety valve

Non condensable drain valve

VU1

Oil non-return valve

VU2

One-way valve

VU3

UV contrast medium non-return

valve

Summary of Contents for ACS 511









































Search results

Summary of Contents for ACS 511

Reviews:

Related manuals for ACS 511

Brands by name

Popular brands

Bosch ACS 511, Repair Instruction

Search results

Summary of Contents for ACS 511

Reviews:

Related manuals for ACS 511

Brands by name

Popular brands