Bosch Rexroth IPC Connectivity Manual Download Page 85 | Manualshive

Page: 85 / 99

background image

Maintenance and Replacement

8–13

1070 073 822-104 (02.06) GB

Arrangement of expansion slots in the housing

ISA slot A5

ISA/PCI slot A1

PCI slot A2

PCI slot A3

PCI slot A4

ISA slot A6

Slot cover

If the card is Plug-and-Play (PnP) compatible, it is automatically recognized
and integrated in the system, provided this creates no hardware conflicts
(IRQ, etc.) with other expamnsion cards or connected devices.

In the event that subsequent to a system reboot the functions based on the
newly aded card are not available, there may be several reasons for this:

D

The card is not properly seated in the PCI or ISA slot contacts.

D

The software driver for the card has not been installed or its installation is
faulty.

D

IRQ (interrupt) conflict with other PC hardware components.

D

The software for the card has not been installed.

CAUTION
Destruction of main board or ISA cards through address conflicts
(IRQ, memory access, I/O address)!
Observe the information provided by the card manufacturer. You
may have try out new configuration settings in both BIOS and operat-
ing system.

«
...
83
84
85
86
87
...
»

Summary of Contents for IPC




































































































Reviews:

No comments

Related manuals for IPC

Brand: TAS Pages: 25

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: SCHUNK Pages: 2

Weigh Scale Blender

Brand: MAGUIRE Pages: 141

EAS-dutytorque 404 0400 Series

Brand: Mayr Pages: 15

Brand: Ampetronic Pages: 8

Brand: Giebel Pages: 9

Brand: Scotchman Pages: 32

Brand: Jäger Pages: 40

Brand: CNC Pages: 18

7x7 NG Plus 4 Series

Brand: Monosem Pages: 94

Brand: Wacker Neuson Pages: 168

RA 240 D2x3 IE2

Brand: Ringler Pages: 56

Brand: OEZ Pages: 8

Brand: Makita Pages: 2

Brand: Balluff Pages: 26

Brand: PFlow Industries Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands