Bosch Rexroth IndraControl VAC 01 Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 40

Bosch Rexroth IndraControl VAC 01 Operating Instructions Manual Download Page 12

3.4 Signal graphic explanation on the device

krax

Prior to the installation and commissioning of the device, refer to the

device documentation.

4 Intended use

The Y-repeater is required to connect two operator displays to a control cabinet

PC.

Risk of damaging of the device if not expressly
stated accessories, mounting parts and other
components, cables, and lines are used.

NOTICE

The Y-repeater may be used only as intended and with the accessories, mount-

ing parts and other components specified in this documentation. Components

that are not expressly mentioned must neither be attached nor connected. The

same applies to cables and lines.
Operation must only be carried out with the hardware component configura-

tions and combinations that are expressly specified.

The Y-repeater can be used for the following IndraControl V device:

●

Control cabinet PC Rexroth IndraControl VSB 40.3

The Y-repeater may only be operated under the mounting and installation condi-

tions, the position, and the ambient conditions (temperature, degree of protec-

tion, humidity, EMC etc.) specified in the related documentation.

5 Accessories

5.1 External 24 V power supply unit

Ordering code

Part number

Description

VAP01.1H-W23-024-010-NN

R911171065

External 24 V power supply unit for UPS

and IndraControl V-devices

Tab. 5-1: Ordering data, 24 V power supply unit for UPS and IndraControl V-devices

Bosch Rexroth AG
Accessories

Y-Repeater

6/33

DOK-SUPPL*-VAC*01*****-IT03-EN-P

«
...
10
11
12
13
14
...
»

Summary of Contents for IndraControl VAC 01









































Reviews:

No comments