background image

General Safety Instructions

WARNING

Do not use the rotisserie in the rain.

WARNING

Electrical Grounding Instructions

This appliance (rotisserie motor) is equipped with 

a three-prong (grounding) plug for your protection

against shock hazard and should be plugged

directly into a properly grounded three-prong 

receptacle. DO NOT cut or remove the grounding

prong from this plug.

WARNING

Keep any electrical supply cords and the fuel 

supply hose away from any heated surfaces.

WARNING

The Spare L.P. Gas Tank Barrier must be installed 

to prevent storage of spare L.P. Gas Tanks. Failure to

comply with these instructions could result in 

a fire or explosion that could cause serious 

bodily injury, death, or property damage.

FOR YOUR  SAFETY

If you smell gas:

1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open grill hood.
4. If odor continues, immediately call 

your gas supplier and local 
Fire Department.

This appliance is not intended to be installed

in or on recreational vehicles or boats.

WARNING

NOTE: DO NOT operate the main burners and

infrared back burner at the same time. This can

cause warping of the roll top grill hood.

WARNING

DO NOT

use the grill in garages, breezeways, sheds 

or any enclosed area. Never operate the grill in 

enclosed areas as this could lead to a carbon 

monoxide buildup, which could result in injury or 

death. Place the grill on a level surface. Avoid 

moving the grill while it is in operation.

WARNING

Always have a qualified service technician perform 

difficult conversions or modifications.

WARNING

Never attach an unregulated gas line to the 

appliance. Connection to an unregulated gas

line can cause excessive heat or fire

FOR YOUR  SAFETY

DO NOT 

store or use gasoline or other 

flammable vapors and liquids in the vicinity of 

this or any other appliance.

An 

L.P. cylinder 

not connected for use shall not be

stored in the vicinity of this or any other appliance.

WARNING

DO NOT

try lighting this appliance without reading the

"LIGHTING INSTRUCTIONS"

section of this manual.

THIS GRILL IS FOR OUTDOOR USE ONLY

Installation must conform with local codes

Summary of Contents for Bernini


























Reviews: