BORETTI BCHSB-60, Instructions For Use Manual

Page: 18 / 39

CONTROLS
Key A = turns the lights on/off.
Key B = turns the TIMER on/off: press once to turn the timer on, therefore,
after 5 minutes, the motor cuts out (at the same time the selected speed
blinks on the display); the timer remains on if the motor speed is changed.
Display C =
- indicates the selected motor speed (from 1 to 4);
- indicates Timer On when the number blinks;
- indicates Filter Alarm when the central segments is on or blinking.
Key D = makes the motor work (at the last speed selected); pushing the
button again, the speeds of the motor are sequentially selected from 1 to 4;
keeping this button pressed for about 2 seconds shuts down the motor.
Key R =
appears (i.e. when the central segment on the display goes on), the grease
alarm can be seen when the motor is off and for about 30 seconds. To reset
the hour counter, keep the button pressed for 2 seconds while the alarm
CONTROLS
AUTOMATIC OPERATION WITH SENSOR:
Key A : switches the lights on/off.
Key B :
enables/disables “Automatic” function. When this function is
selected, an “A” appears on the display C, and the speed of the motor
increases or decreases depending on the smoke, odours and gas present
in the kitchen.
Display C :
- indicates the automatic operation of the sensor (the letter “A” appears);
- indicates the motor speed selected automatically by the sensor;
-
Key D : decreases motor speed / Reset; decreases motor speed to zero
(stopping); in any case however, after approximately 1 minute, the hood
resumes automatic operation at the speed set by the sensor. Whenever the
counting of the hours resumes again.
Key E : increases motor speed; in any case however, after approximately
1 minute, the hood resumes automatic operation at the speed set by the
sensor.
- Stop the hood by pressing key B.
- Simultaneously press keys D and E (the sensor’s sensitivity index will
appear on the display).
- Pressing keys D or E, the sensor’s sensitivity will either increase or
decrease (1 : minimum sensitivity / 9: maximum sensitivity).
- whenever the power supply is interrupted, the sensor will resume opera-
tion with a sensitivity index of 5.
Warning: in order to avoid damaging the sensor, never use silicone
products near the hood!
OPERATION AS TRADITIONAL HOOD:
Key A :
switches the lights on/off.
Display C :
- indicates the motor speed selected (from 1 to 4);
-
-
Key D : decreases motor speed / Stop / Reset; decreases motor speed to
, a
RESET occurs, and the counting of the hours resumes again.
Key E : enables the motor / increases motor speed /TIMER. Pressing
this key starts the motor (at the latest speed set); pressing the key again
increases motor speed, while keeping the key pressed down for a few se-
conds enables the TIMER, and 5 minutes later the motor will stop (while the
display); the Timer will remain enabled if motor speed is changed. In order
to disable the Timer, press the key again.
A B D
OPERATION INSTRUCTIONS
SETTING THE CLOCK (to be done with the hood in stand-by)
2) change the hour by pressing Button 2 ( - ) or Button 3 ( + )
4) change the minutes by pressing Button 2 ( - ) or Button 3 ( + )
5) press Button 1 to return to normal view. The time has now been set
TURNING THE LAMPS ON AND OFF (place alongside the lamp picto-
gram)
Press Button 2 to turn the lights on/off. If the lights are on this is also indica
ted by the lighting of the luminous ring around Button 2 and the lighting of
the “Lamp” icon on the display
TURNING ON THE HOOD MOTOR (place alongside the + pictogram)
Press Button 4 to turn on the motor which will start at speed 3 for 2 secon-
ds. Then the hood will set the most recent speed set before the last shut
down.
Or:
Press Button 3 to turn on the motor which will start at speed 3 for 2 secon-
ds. Then the hood will set the most recent speed set before the last shut
down.
If the hood is on this is indicated by the lighting of the luminous ring
around Buttons 3 and 4 and the lighting of the “Speed” icon on the
display
VARIATION OF THE MOTOR SPEED (place alongside pic)
Press Button 3 repeatedly to change the motor speed sequentially, from
slowest to fastest. The motor speed icon turns at a speed proportional to
faster for the third)
ACTIVATION OF THE TIMER FEATU
gram)
time. When the time expires the hood shuts off.
with the motor on:
press Button 1 to activate the Timer feature. When the timer feature is
active the “timer” icon will appear on the display, the luminous ring around
timer is set automatically to 5 minutes, but pushing Button 2 or Button 3
increases/decreases the duration of the countdown
Once the duration of the timer is set, the countdown can be started by
pressing Button 1 (if Button 1 is not pressed within 10” the countdown will
start automatically)
To interrupt the timer and deactivate the feature press Button 1 during the
countdown.
Upon expiry of the countdown the hood will emit a double beep and the
motor will shut off
TURNING THE HOOD OFF (place alongside the
Press Button 4
NOTE:
With the hood in stand-by (lights off, motor off, display off), press any button
to turn on the display back-light without activating any functions. Only by
pressing buttons P2, P3, P4 can their relative functions be activated.
the display turns off and the hood returns to the stand-by mode.
A B C D
A B C D E
A B C D E