background image

10 
 

 

Important: Before removal from the installation, ensure all electrical, product and gas

 

connections are disconnected.

 

 

Disposal of Scrap Units 

 

It is illegal to simply scrap a refrigeration unit. Before a unit can be scrapped it must first have the gas 
removed by a specialist using special equipment. Please contact Booth Dispensers Ltd., who will be 
happy to provide a quotation for disposal. 

 

Transportation

 

 

Important

: This unit must be transported in an upright position 

 
As with all refrigeration systems, irreparable damage can be caused by laying the unit on its side or 
even transporting upside down. Where the unit is transported by a carrier, the carton should always 
be marked in a conspicuous manner, the correct upright position in which it must be handled. 
 
If a unit has been transported incorrectly it should be placed in the correct upright position and left for 
24 hours before attempting to run the system. 
 
Failure  to  observe  the  above  precautions  could  seriously  damage  the  system,  and  would  void  any 
warranty. 

 

 
 
 
 
 

 

Removal, Transportation and Disposal 

 

Booth Dispensers Ltd, Moor Park Avenue, Blackpool, 

Lancashire, FY2 0LZ, UK 

+44 1253 501800 

 

Summary of Contents for EXL651











Reviews: