manualshive.com logo in svg

Bomag BPR 50, Operating Instruction

Share
Download
Bomag BPR 50 Operating Instruction Download Page 73

6.9.4  Changing the oil in the exciter housing

Perform this maintenance work at the latest after 500

operating hours

NOTICE!
Components may get damaged!

–

Use only oil of the permitted specifica-

tion

Ä

 Chapter 6.3 ‘Table of fuels and lubricants’

on page 53

.

Protective equipment:

n

Working clothes

n

Protective gloves

Park the machine on level ground.

Park the machine in secured condition.

Clean the area around oil breather filter (1) and filling/drain

plug (2).

Tilt the machine slightly towards the oil drain side and sup-

port it safely.

Unscrew the bleeding screw.

WARNING!
Danger of burning on hot components!

–

Wear your personal protective outfit (protec-

tive gloves, protective clothing).

Unscrew the filling/drain plug and catch any oil running out.

Tilt the machine to the opposite side and secure it properly.

Fill in new oil.

Fig.  70

Fig.  71

Maintenance – Annual maintenance

 

BPR 50/55 D / BPR 60/65 D

 

73

Go 

to 

Discount-Equipment.com 

to 

order 

your 

parts

Summary of Contents for BPR 50


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands