background image

27 

 

EXPOSURE Menu 

 
The EXPOSURE menu is used to set the items related to exposure. 

 

MODE (Exposure Mode) 
 

FULL AUTO

: The exposure is adjusted 

automatically using the sensitivity, electronic 
shutter speed, and iris. 
 
 
 
 
 

MANUAL

:  

Adjust with variable (GAIN), electronic shutter speed (SPEED) and iris 
(IRIS) manually.  

 

GAIN

: Adjust with Variable Gain (0 to 36 dB, 13 steps, 38 

 

steps on High sensitivity mode), Auto Iris and Shutter speed. 
Select the gain from the following: 
0, 3, 6, 9, 12, 15, 18, 21, 24, 27, 30, 33, 36 dB 

 

GAIN LIMIT: 

The gain limit can be set at Full Auto, Shutter 

Priority, Iris Priority, Bright, Spot Exposure and Manual in AE 
mode. Use this setting when you want to obtain images with a 
focus on the signal-to-noise ratio.  
Select the gain from the following

9,12,15,18,21,24,27,30,33,36DB 

 

SPEED

: Select the electronic shutter speed from the following: 

1/1, 2/3, 1/2, 1/3, 1/4, 1/6, 1/8, 1/10, 1/15, 1/20, 1/30, 1/50, 1/60, 1/90, 1/100, 1/125, 1/180, 1/250, 1/350, 
1/500, 1/725, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/6000, 1/10K sec 

 

IRIS

: Select the iris the following:  

F11, F10, F9.6, F8, F7.3, F6.8, F6.4, F6.2, F5.6, F5.2, F4.8, F4.4, F4.0, F3.7, F3.4, F3.1, F2.8 

 

IRIS PRI

:  

 

Iris Priority mode. The exposure is adjusted automatically using 
the sensitivity and electronic shutter speed. Adjust with Variable 
Iris (F2.8 to F11, 17 steps) manually.  

 

 
 
 
SHUTTER PRI

:  

 

Shutter Priority mode. The exposure is adjusted automatically 
using the sensitivity and iris. Adjust with Variable Shutter Speed 
(1/1 to 1/10,000 sec., 16 high-speed shutter speeds plus 12 low-
speed shutter speeds), Auto Iris and Gain. Adjust the electronic 
shutter speed (SPEED) manually. 

 

BRIGHT

:  

 

Adjust with Variable Iris and Gain (F11 to F2.8, 29 steps and 
High Sensitivity Mode at 33 steps). 

 

 
 
 

GAIN PRI:  

 

Adjust with Variable Gain (0 to 36 dB, 13 steps, 38 steps on High 
sensitivity mode), Auto Iris and Shutter speed. 

 

 
 
 
 
 

MODE     MANUAL 

>

GAIN                    9DB 

>

GAIN LIMIT        12DB 

>

SPEED                  1/100 

>

IRIS                       F2.8 

EXPOSURE MENU: MANUAL 

MODE     IRIS PRI 
  IRIS                       F2.8 

>

GAIN LIMIT        12DB 

  MAX SHUTTER  1/350 
  MIN SHUTTER    1/10 
EX-COMP               OFF 

>

 

EXPOSURE MENU: IRIS PRI 
 

MODE     SHUTTER PRI 
  SPEED                   1/100 

>

GAIN LIMIT         12DB 

  EX-COMP                OFF 

>

 

EXPOSURE MENU: SHUTTER 
PRI 

MODE     BRIGHT 
  LEVEL                            1/100 

>

GAIN LIMIT                   12DB 

  HIGH SENSITIVITY        OFF 

>

 

EXPOSURE MENU: BRIGHT 
 

MODE     BRIGHT 
  GAIN                                 9DB 

>

GAIN POINT                    OFF 

  HIGH SENSITIVITY        OFF 

>

 

EXPOSURE MENU: GAIN PRI 
 

>EXPOSURE 

>

WHITE BALANCE 

>

PICTURE1 

>

PICTURE2 

  GAMMA 

>

ZOOM 

>

SYSTEM 

 

OSD 

MODE     FULL AUTO 
SLOWSHUTTER        

OFF 

MAX SHUTTER         

1/350 

MIN SHUTTER           

1/10 

HIGH RESOLUTION  

OFF 

SLOW AE                     

030 

GAIN LIMIT                

12DB 

EX COMP                    

OFF 

 

EXPOSURE MENU 
 

Summary of Contents for 1 Series











































Reviews: