background image

Successful  fitness  training  programs  have  one  prominent  feature  in  common...safety.  Fitness  training 

has some inherent dangers, as do all physical activities. The chance of injury can be greatly reduced 

or completely removed by using correct techniques, proper breathing, maintaining equipment in good 

working condition, and by wearing the appropriate clothing.

•  It is highly recommended that you consult your physician before beginning any exercise program. This is 

especially important for individuals over the age of 35, or persons with pre-existing health problems.

•  Always warm up before starting a workout. Try to do a total body warm up before you start. 
•  Maintaining equipment in proper operating condition is of utmost importance for a safe training program.
•  Keep hands, limbs, loose clothing and long hair well out of the way of all moving parts.
•  Inspect the machine before each use for loose or worn parts. Ensure all nuts and bolts are fully tightened. If a 

problem is found do not allow the machine to be used until all parts are tightened or worn or defective parts are 

repaired or replaced.

SAFETY 

GUIDELINES

5

Summary of Contents for ABX290M





















Reviews: