background image

3

CHAPTER 1 : INTRODUCTION

EXPLANATION OF PAIN

Pain is a warning system and the body’s method of telling us that something 
is wrong. Pain is important; without it abnormal conditions may go 
undetected, causing damage or injury to vital parts of our bodies.

Even though pain is a necessary warning signal of trauma or malfunction in 
the body, nature may have gone too far in its design. Aside from its value in 
diagnosis, long-lasting persistent pain serves no useful purpose. Pain does 
not begin until a coded message travels to the brain where it is decoded, 
analyzed, and then reacted to. The pain message travels from the injured 
area along the small nerves leading to the spinal cord. Here the message is 
switched to different nerves that travel up the spinal cord to the brain. The 
pain message is then interpreted, referred back and the pain is felt.

EXPLANATION OF TENS

Transcutaneous Electrical Nerve Stimulation is a non-invasive, drug free 
method of controlling pain. TENS uses tiny electrical impulses sent through 
the skin to nerves to modify your pain perception. TENS does not cure any 
physiological problem; it only helps control the pain. TENS does not work for 
everyone; however, in most patients it is effective in reducing or eliminating 
the pain, allowing for a return to normal activity.

HOW TENS WORKS

There is nothing “magic” about Transcutaneous Electrical Nerve Stimulation 
(TENS). TENS is intended to be used to relieve pain. The TENS unit sends 
comfortable impulses through the skin that stimulate the nerve (or nerves) 
in the treatment area. In many cases, this stimulation will greatly reduce or 
eliminate the pain sensation the patient feels. Pain relief varies by individual 
patient, mode selected for therapy, and the type of pain. In many patients, 
the reduction or elimination of pain lasts longer than the actual period of 
stimulation (sometimes as much as three to four times longer). In others, 
pain is only modified while stimulation actually occurs. You may discuss this 
with your physician or therapist.

Summary of Contents for ZZAN602





















Reviews: