T1
T4
T6
T7
T8
T9
T5
T3
T2
STEP 4 Top Cable Assembly
T5
61
110 24
130
51
37
T9
130
61
26
110
T3
61
27
110
130
T7
TOP CABLE (51)
bolt end
ball with hook end
9
T1
61
3
122
122
108
130
3
T2
61
108
130
122
122
T4
130
108
61
3
61
13
110
110
T6
130
130
T6,T8
T8
Assemble cables and pulleys simultaneously
1. Start by inserting the threaded end of the Top Cable (51) into the slot in the front of the Top Frame (3) as
shown in inset T1. Then insert a pulley into the slot, making sure the cable is seated in the pulley groove and
running over the top of the pulley. Attach the pulley to the Top Frame (3) using one 3/8" X 2-3/4" Hex Bolt
(108), two 3/8" Washers (122) and one 3/8" Nylon Nut (130).
2. Push the cable through the Top Frame (3) until it emerges from the slot just behind the Front Upright. Mount a
pulley in the slot using one 3/8" X 2-3/4" Hex Bolt (108), two 3/8" Washers (122) and one 3/8" Nylon Nut (130)
as shown in inset T2.
3. Find the Single Pulley with Stopper (26). Run the Top Cable (51) through the center. Attach a pulley to the
Single Pulley with Stopper (26) using one 3/8" X 1-3/4" Hex Bolt (110) and one 3/8" Nylon Nut (130) as shown
in inset T3. The cable runs along the side nearest the threaded end, not the side with the flat top. Let the
Single Pulley with Stopper (26) dangle. It does not attach to the frame.
4. Grab two pulleys and hold them side-by-side. Mount the pulleys to the Top Frame (3), as shown in inset T4,
while ensuring the Top Cable (51) is running over top of the outside (left side) pulley. Use one 3/8" X 2-3/4"
Hex Bolt (108) and one 3/8" Nylon Nut (130). Do not tighten this bolt. You will need to remove it when routing
the Connecting Cable (51A).
5. Find the Pulley Block with Screw (27). Screw it into the threaded receptor on the Top Guide Rod Retainer (13)
approximately half way. Run the Top Cable (51) through the Top Guide Rod Retainer (13) and then screw the
end of the Top Cable (51) into the Top Plate (36), approximately half way, as shown in T9. Insert a pulley into
the Pulley Block with Screw (27), ensuring that the cable runs below the pulley and is seated in the groove.
Secure the pulley using one 3/8" X 1-3/4" Hex Bolt (110) and one 3/8" Nylon Nut (130) as shown T7.
6. While routing the Top Cable (51) over top, attach pulleys T6 and T8 to the Top Guide Rod Retainer (13) using
one 3/8" X 1-1/4" Hex Bolt (110) and one 3/8" Nylon Nut (130) in each as shown.
7. Mount a pulley in the top hole (nearest the closed side) of the Floating Pulley Block
(24), using one 3/8" X 1-3/4" Hex Bolt (110) and one 3/8" Nylon Nut (130). Pull some
slack in the Top Cable (51) in between T4 and T6. Slip the cable into the Floating
Pulley Block (24) making sure it seats in the pulley groove. The Floating Pulley Block
(24) does not attach to the frame.
Cable adjustments are made at the end.
