15
STEP 7 INSTALL TOP CABLE
TOP CABLE (82)
Threaded End
Ball End
*Assemble cables and pulleys simultaneously.*
On the following pages, when references are made regarding the
LEFT, RIGHT and FRONT of the machine, the directions are as if
you are seated in the gym with your back against the Back Pad.
The
Bolt-end
must be at least a 1/3 into the T
OP PLATE ASSEMBLY (58)
.
Tighten
the
Jam-nuts
located on both
1/2" STOPPERS (93)
.
Tighten
the pulleys located in both
ADJ. PULLEY BLOCKS (23)
.
1. See Fig. 1 Insert the
Bolt-end
of the
TOP CABLE (82)
through the bottom of the front slot
of the
TOP FRAME (4)
, then over
Pulleys T1
and
T2
as shown. Secure each pulley using
one
3/8" X 109.5L FLAT PIN BOLT (140)
and one
M6 X 12L MALE SCREW (147)
.
Tighten
.
NOTE!
The cable runs above the
TOP FRAME (4)
,
NOT
inside the tube.
2. See Fig. 2 Countinue routing the cable entering the top and exiting on bottom of the
Left
Side Pulley T3
mount to the
PRESS ARM SUPPORT (9)
using one
3/8" X 2-3/4" HEX
BOLT (142)
and one
3/8" NYLA-NUT (170)
.
DO NOT Tighten.
Route cable around
Pulley
T4
mounted on the
FRONT UPRIGHT (3)
by entering the bottom and exiting the top.
Secure using one
3/8" X 1-3/4" HEX BOLT (134)
and one
3/8" NYLA-NUT (170).
Tighten.
3. See Fig. 3 Route the cable around
Right Side Pulley T5
mounted in the
PRESS ARM
SUPPORT (9)
, by entering the top and exiting the bottom.
Tighten.
4. See Fig. 4 Route the cable under
Pulley T6
and mount in the slot in the
FRONT UPRIGHT
(3)
using one
3/8" X 1-3/4" HEX BOLT (134)
and one 3
/8" NYLA-NUT (170)
. Continue to
route the cable over
Pulley
T7
and mount to the top rear of the
FRONT UPRIGHT (3)
using
one
3/8" X 109.5L FLAT PIN BOLT (140)
and one
M6 X 12L MALE SCREW (147)
.
Tighten.
5. See Fig. 5 Install a
4-1/2" PULLEY (100)
into each of the
ADJ. PULLEY BLOCKS (23)
in
the second hole below the welded stop plate. (
DO NOT TIGHTEN
. You may need to move
the pulleys when adjusting the cables).
6. See Fig. 6 & 7 Route the cable over
Pulleys T9
and
T11
mounted to the
TOP FRAME (4)
while simultaneously routing the cable under the installed
Pulleys T8
and
T10
mounted in
the
ADJ. PULLEY BLOCKS (23)
. (
NOTE!
The
ADJ. PULLEY BLOCKS (23)
do not attach
to the frame, they are held in place by the cable). Secure
Pulleys T9
and
T11
using one
3/8" X 1-3/4" HEX BOLT (134)
and one
3/8" NYLA-NUT (170)
.
Tighten
Bolts
at
T9
and
T11
.
7. See Fig. 8 Secure the
TOP CABLE (82)
by threading the
Bolt-end
at least a third of the
way into the
TOP PLATE ASSEMBLY (58)
.
Tighten
Jam-nut
on the
Bolt-end
against the
TOP PLATE ASSEMBLY (58)
.
8.
Top Cable Adjustment
. There are multiple adjustment points. Remove cable slack by
adjusting the two preinstalled
1/2" STOPPERS (93)
down onto the plates welded to the top
of the
ADJ. PULLEY BLOCKS (23)
equally to remove all cable slack. If the slack cannot
be completely removed, adjust one or both pulleys located in the
ADJ. PULLEY BLOCKS
(23)
down one or move holes or adjust the
Bolt-end
of the cable in the
TOP PLATE
ASSEMBLY (58)
.
