background image

BOB’S SPACE RACERS® 

 

 

 

 

 

      BIG DOG (KIDDIE DOG POUNDER)™ ARCADE 

 

14

5-2-1. Mechanical Repair: 

 

HAMMOCK REPLACEMENT 

 

A common service on this game will be occasional replacement of the ball hammock. 
 

NOTE: THE MATERIAL USED IN THIS GAME HAS BEEN CAREFULLY SELECTED FOR MAXIMUM 
PERFORMANCE AND RELIABILITY.  USE OF ANY OTHER MATERIAL WILL ADVERSELY AFFECT THE 
PERFORMANCE OF THE GAME AND COULD ACTUALLY DAMAGE COMPONENTS OF THE AIR LEVER 
ASSEMBLY.  USE OF ANY MATERIAL OTHER THAN THAT SUPPLIED BY BSR GAMES, WILL 
CONSTITUTE A BREACH OF WARRANTY QUALIFICATIONS AND WILL VOID YOUR WARRANTY ON 
THOSE RELATED COMPONENTS. 

 
1. To replace the hammock, remove the 3 screws that hold 
the window retainer bracket to the top of the control panel 
and remove the bracket. 
 
2. Remove the front window assembly by lifting straight up 
on it and then tilting it out from the bottom. 
 
3. Remove the 5 screws that hold the front of the hammock 
to the lever assembly. 
 
4. Remove the 5 nuts and bolts that hold the rear of the  
hammock to the metal shelf. 
 
5. Install the new hammock to the metal shelf. Be  
sure that the reinforcement strip is facing up so that 
it clamps the hammock material to the shelf.  Tighten 
the bolts securely, but not so much as to excessively 
distort the reinforcement strip. 
 
6. Attach the front of the hammock to the lever  
assembly with the 5 bolts. After tightening bolts place 
and tighten the nuts on the back side accordingly to 
double lock the fasteners. 
 
A) Hammock placed against lever assembly. 
B) Aluminum angle bracket with rubber facing the  
    plastic strips. 
C) Use only BSR complete assembled hammocks  
    as replacement parts. 
 
7. Tighten the nuts and bolts securely, but not so much as to excessively distort the reinforcement strip. 
 
8. Test the unit for proper operation including the proper operation of the release lever. 
 

NOTE: IT IS CRITICAL TO THE OPERATION OF THE GAME THAT THIS INSTALLATION IS FOLLOWED 
CORRECTLY.  IF YOU HAVE ANY CONCERNS, PLEASE CALL OUR SERVICE DEPARTMENT BEFORE 
PROCEEDING.

 

 

PIVOT MECHANISM GROUND WIRES REPLACEMENT 

 
1. Remove A.C. power to the game. 
2. Unlock and open front door. 
3. Remove nut from bolt to release ground wires from the top left corner of coin box.  
4. Remove nut from bolt to release ground wire on pivot mechanism towards the front near the hammock. 
5. Replace braided ground wire (Part # EX800429) and reattach nut. 

DO NOT OVERTIGHTEN THIS NUT! 

6. Remove nut from bolt to release ground wire on pivot mechanism under counter. 
7. Replace braided ground wire (Part # EX800433) and reattach nut.

 DO NOT OVERTIGHTEN THIS NUT! 

 

FRONT 
WINDOW 
 
WINDOW 
RETAINER 
BRACKET

 

LEVER 
ASSEMBLY 
 
 
HAMMOCK 
 
METAL 
SHELF

Summary of Contents for Big Dog Kiddie Dog Pounder






































Reviews: