WarninG: turn eLeCtriCaL poWer suppLy off Before
maKinG eLeCtriCaL ConneCtions. Dryer must Be
GrounDeD (eartheD).
7/8''
(22mm)
3-17/32''
(90mm)
3/4''
(18mm)
Entry Hole
for Between-Wall Wiring
5/8''
(16.5mm)
Entry Point
for Surface Mounted Wiring
8-3/32''
(205mm)
4-17/32''
(115mm)
Mounting Base
C
L
Horizontal
Reference
Horizontal
Reference
3-15/16''
(100mm)
7-7/8''
(200mm)
4-11/32''
(110mm)
Electrical Characteristics
Recommended Mounting Heights
Removal of Cover
Installation of Mounting Base
Electrical Connection
Page 2
model B-710,115V AC, 15 Amp, 1725 Watts, 60 HZ, Single Phase, cULus listed.
model B-710e, 220-240V, 7A, AC 1500-1700 Watts, 50/60 Hz, Single Phase; VDE approved, CE marked. B-710e is not available in the united
states and Canada.
Installation instructions and template provide information that will assist in the installation of the Bobrick B-710 115V, B-710E 220-240V. Retain
Installation Instruction Sheet for important maintenance instructions and warranty information.
Distance from floor to bottom mounting screw holes of mounting base.
Men's Washrooms ....................................................................................................................................................................46''
(1170mm)
Women's Washrooms ...............................................................................................................................................................44''
(1120mm)
Children's Washrooms, ages 3-9 .............................................................................................................................................32''
(815mm)
Children's Washrooms, ages 9-12 ............................................................................................................................................36''
(915mm)
Children's Washrooms, ages 12-15 ..........................................................................................................................................40''
(1015mm)
Children's Washrooms, ages 15-18 ..........................................................................................................................................44''
(1120mm)
Barrier-Free Design ..................................................................................................................................................................38''
(965mm)
1. Start installation of dryer by
removing cover. Remove three
screws, one from each side and
one from the bottom of the
dryer. Lift the cover from the
mounting base.
1. Hold the Installation Template against the wall in the desired location of the
installed dryer, see recommended mounting heights above.
2. Make sure line on template representing bottom of dryer mounting base is
horizontal and located at the desired height above floor.
3. Mark center of four mounting screw holes and hole for entry of electrical
wiring if electrical supply is concealed in wall and will enter dryer from back
through mounting base.
NOTE: Surface-mounted electrical supply entry is located in the lower right corner
of the mounting base. Bottom of mounting base has 1/2'' square (13mm) opening in
lower right corner to accommodate connection of electrical conduit.
4. Drill four holes for #10 (M4.8) mounting bolts or screws (not furnished).
5. For masonry walls provide four #10 expansion shields or anchors and secure
with four #10 (M4.8) sheet-metal screws (not furnished). For plaster or dry
wall construction, provide concealed backing to comply with local building
codes and secure with four #10 (M4.8) round-head sheet-metal screws, or
3/16'' (5mm) toggle bolts (not furnished).
NOTE: Use 2'' (50mm) long screws in top two mounting holes. Use 3'' (75mm) long
screws in lower two mounting holes.
6. Fasten mounting base securely to wall.
for proper eLeCtriCaL ConneCtions, CheCK LoCaL BuiLDinG CoDe. unit must Be instaLLeD By a quaLifieD LiCenseD
eLeCtriCian. WarninG: turn eLeCtriCaL poWer suppLy off Before maKinG eLeCtriCaL ConneC tions.
1. Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In the United States and Canada use #12 wire.
2. Wiring Instructions:
a) A fused means for disconnection in all poles must be provided in the fixed wiring in accordance with the wiring rules.
b) Trim insulation from end of electrical wire.
c) Remove screws in strain relief clamp. Remove clamping crossbar. Feed electrical wire through clamp.
d) Make connection to terminal block as follows:
1) 115V: Connect ground (earthed) wire to ground (earthed) terminal marked . 220-240V Dryers are doubled insulated and should not be
fitted with an earth (ground) wire.
2) Connect the black or
Hot
wire to terminal marked
L1
.
3) Connect the white or neutral wire to terminal marked
N
.
e) Replace crossbar on strain relief clamp. Tighten screws securing electrical wire.
NOTE: DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER.
*
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the
operation of the automatic sensor.
