background image

Page | 9

BN Products-USA

www.bnproducts.com

     

MAINTENANCE

Other than Carbon Brushes, there are no parts fitted inside the unit that 
require maintenance.

CORRECTIVE ACTION IN CASE OF FAILURE

The operating switch is switched on, but the motor is not working.

•  Wires in the electric plug or in the socket are loose. Have socket and 

plug checked or repaired or replaced.

•  The switch is faulty. Have the switch replaced.

The operating switch is switched on, but unusual noises can be heard, 
the motor is not working or only very slowly.

•  Switch contact has failed. Have the switch replaced.
•  Component jammed. Have the electric tool checked or repaired.

Motor gets hot.

•  Foreign substances have got inside the motor. Have the foreign sub-

stances removed.

•  Lack of or contaminated lubrication grease. Have lubricating grease 

applied or replaced.

•  Pressure too high. Use less thrust during the task

Frequent or strong sparks on the commutator.

•  Short circuit on the armature. Have the armature replaced.
•  Carbon brushes worn out or jammed. Have the carbon brushes 

checked.

•  Rough running of the commutator. Have the surface of the commuta-

tor cleaned or ground.

For your own safety, never remove parts or accessories of the electric tool 
during operation, In case of fault or damage have the electric tool repaired 
only by a specialist workshop or by the manufacturer.

Summary of Contents for BNR6502













Reviews: