background image

BMG LABTECH 

 

PHERAstar 

FS

 Operating Manual 

2009-09-22  

0471B0001A 

17/26 

 

If the assay demands a specific wavelength to be measured, this can be carried out by having a filter in front 
of the measurement channel. And if the demand is to measure two different wavelengths, this can be carried 
out by including a dichroic mirror and a second filter in front of the emission channel B, for example BRET 
assays. (figure 22). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 22: Left: luminescence optic module to measure light of a specific wavelength 
Right: luminescence optic module to measure light of two specific wavelengths 
 
 

4.5.5 AlphaScreen

®

 Module 

AlphaScreen

®

 is a unique assay technology that measures the interaction of two molecules bioconjugated to 

donor and acceptor beads. When interactions occur between these molecules, the beads are brought close 
enough to cause a chemical reaction. Upon laser excitation at 680 nm, a singlet oxygen transfer occurs that 
leads to a strong light emission between 520 to 620 nm, which is directly proportional to the amount of 
binding (figure 23). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
Figure 23: Optic Module for single channel  
AlphaScreen

® 

measurement 

 
 
 
 
 
 
 
 
 

Summary of Contents for PHERAstar FS



























Reviews: