manualshive.com logo in svg

BLUM MZK.1900, Instruction Leaflet, Page: 17 / 20

Share
Download
BLUM MZK.1900 Instruction Leaflet Download Page 17

17

BA-092/0EN MZK.1900/8800

Error

Cause

Solution

Note

Drilling head can-

not be attached

Incorrect retainer is attached

Attach correct retainer  

(see retrofit kit M30.1313.UMBO-K)

Incorrect driving pin used

Use correct driving pin

See point 2.2

Chips between retainer, drilling head 

and drilling head attachment

Remove chips

none

Locking mechanism 

3.3

 is closed

Set locking mechanism to open

See point 3.1 

Drill bit cannot 

be tightened or 

removed

Drill bit surface for tightening too large

Dimension (9.3 mm)

Only use Blum-approved drill bits. See 

Blum product catalogue or www.blum.com

See chapter 1

Bit interior fouled by chips

Blow out drilling head and bits, remove bit 

coverings 

See chapter 1

Dirt and dust between locking ring and 

bits

Blow out drilling head and bits, remove bit 

coverings 

See chapter 1

System drilling not 

parallel to ruler

Drilling head turns out of position 

Retainer and gearbox casing are not 

screwed in correctly

Retighten screws

See instructions 

MA-454

Drilling head is not secured correctly 

(Ioose) 

Close locking mechanism 

(3.3)

 

See instructions 

MA-454

Longer system drill-

ings are uneven

The system drilling has been drilled 

using the locating pins, the range of 

locating pins 

(1.1)

 is too wide.

Drill longer system drillings using stops

See chapter 4

Stops are not set correctly

Check stop settings

See chapter 4

locating pins were not centred cleanly

locating pins must be reset

See chapter 4

Drilled through into 

the work table

Drilling depth spacing was not attached Attach drilling depth spacing

See chapter 2

Drilling depth does 

not match

Incorrect drill bit used

Only use Blum-approved drill bits. See 

Blum product catalogue or www.blum.com

See chapter 1

Drill bit not tightened correctly

Soiling

See chapter 1

Drill bit length is not set properly

See chapter 1

 

6 - Troubleshooting

Summary of Contents for MZK.1900





















Reviews:

No comments