background image

Bluetooth connection loss/ recovery

The headset maybe disconnected if the link between the phone and your headset is lost, 
for example, if the phone and the headset are more than 10 meters (33 feet) apart. 

If the headset is disconnected, the headset will automatically try reconnecting within 
approximately 5 minutes, and you will hear a periodic beep. The music will automatically 
start again if the connection is re-established within 5 minutes. 

If the connection is not re-established after 5 minutes, you have to press once on the 
“TALK/ON/OFF” button       to reconnect the headset with the phone manually.

Note:
This function may not be available on some phones.
Some phones will close the music player if the link is disconnected. In this case, you 
need to restart the music player.

Troubleshooting guide

The first thing you should do if you encounter a problem that you cannot solve with this 
manual, is to switch off your headset and your mobile phone, and then switch them on 
again.

To find out more, please refer to the Troubleshooting/Frequent Asked Questions sections
 of our website: www.bluetrek.com/support/faq

1

En

gl

is

h

14

Summary of Contents for ST1

















Reviews: