background image

4

IMPORTANT SAFETY INSTRUCTIONS

Please examine equipment before use. If there are any damaged or missing parts at the time of 
purchase, do not assemble or operate until parts are replaced. 
To lessen the risk of serious injury or death, follow these rules.
The following instructions contain important safety information, please read these important safety 
instructions and abide by them when installing and using this pool. When installing and using the 
electrical equipment, basic safety precautions must always be followed. 
This includes the following:

WARNING! 

Children have drowned in swimming pools. 
Ensure active adult supervision at all times. Do not leave children unsupervised in or 
around the pool. Keep them within arms reach.

WARNING: 

Consult local municipality, water authority, and building codes in regard 

to the use of water and/ or water restrictions relating to this product.

WARNING: 

Pool fencing laws affect this product, consult the local municipality for applicable 

building codes. Abide by state and federal law requirements such as fencing, enclosures, childproof 
gates, etc.

WARNING: 

Always remove pool ladder when not in use. Store in a place where it is not accessible  

to children.

DANGER:

 Prevent the risk of accidental drowning. Extreme caution must be exercised to prevent 

unsupervised access by children. To avoid accidents, ensure that children cannot use the pool unless 
they are always supervised by an adult. NEVER LEAVE CHILDREN UNATTENDED.

RISK OF ELECTRIC SHOCK:

 Connect filter pump only to a grounding type receptacle protected by 

a GFCI (Ground Fault Circuit Interrupter). Use a qualified electrician to install the GFCI, which has a 
maximum rate of 30A.

WARNING: 

Always know where the cut-off switch for the pump is, so it can be turned off in an 

emergency. It is necessary to have the GFCI Cut-Off Switch plug accessible after installation of  
the pool.

WARNING:

 To avoid electrocution, do not permit electric devices i.e., electric lights, telephone, 

radio, television, hair dryer, etc. within 8-ft of this pool.

WARNING:

 Do not touch the filter pump unless the area around it is completely dry.

WARNING: NEVER

 allow horseplay, diving or jumping into or around the metal wall pool.  

WARNING: NEVER

 enter the pool via any decks or other raised surface, the water level of the pool 

is shallow. Serious injury, paralysis, or death could result.

CAUTION: 

It is advisable to wear protective gloves when assembling pool.

WARNING:

 Follow all safety and installation instructions provided with the filtration system, ladder, 

and skimmer.

Summary of Contents for SAVANNAH NB19821
























Reviews: