Blue Seal 203926 Service Manual Download Page 21

Page: 21 / 76

-21-

Revision 7/F3527

Moffat Ltd, November 2004

FAULT

POSSIBLE CAUSE

REMEDY

DOOR DOES NOT CLOSE

Tray in way of door.

Door seal obstruction.

Door handle installed
incorrectly.

Door catch setting incorrect.

Door pivot bushes / pins worn.

Correctly position tray in rack.

Correctly install door seal.

(Refer service section 6.3.25)

Fit correctly.

(Refer installation section)

Adjust.

(Refer service section 6.4.5)

Replace.

(Refer service section 6.3.26)

DOOR SEAL LEAKS

Door seal damaged.

Door seal incorrectly fitted.

Door catch setting incorrect.

Door pivot bushes / pins worn.

Door catch striker plate worn.

Replace.

(Refer service section 6.3.25)

Correctly install door seal.

(Refer service section 6.3.25)

Adjust.

(Refer service section 6.4.5)

Replace.

(Refer service section 6.3.26)

Replace.

(Refer installation
instructions—Door handle
installation)

Summary of Contents for 203926













































































Search results

Summary of Contents for 203926

Reviews:

Related manuals for 203926

Brands by name

Popular brands

Blue Seal 203926, Service Manual

Search results

Summary of Contents for 203926

Reviews:

Related manuals for 203926

Brands by name

Popular brands