background image

601  

75815

  Owner

M

anual In

tegri

ty Decante

r B

rewers 

NOTE:  

For your protection, please note that equipment in 

this shipment was carefully inspected and packaged by 
skilled personnel before leaving the factory.   
Upon acceptance of this shipment, the transportation       
company assumes full responsibility for its safe delivery.

 

IF SHIPMENT ARRIVES DAMAGED:

 

1.

 

VISIBLE LOSS OR DAMAGE:

    Be  certain  that  any 

 

visible  loss  or  damage  is  noted  on  the  freight  bill  

 

or express receipt, and that the note of loss or damage 

 

is signed by the delivery person. 

2. 

FILE CLAIM FOR DAMAGE IMMEDIATELY: 

 

  

Regardless of the extent of the damage. 

3. 

CONCEALED LOSS OR DAMAGE: 

 if damage is 

        unnoticed until the merchandise is unpacked, notify the           
        transportation company or carrier immediately, and file    
        “CONCEALED DAMAGE” claim with them.  This 
        must be done within fifteen (15) days from the date the  
        delivery was made to you.  Be sure to retain the 
        container for inspection. 

 

Wells Bloomfield cannot assume liability for damage or loss 
incurred in transit.  We will, however, at your request, supply 
you with the necessary documents to support your claim. 

WARRANTY STATEMENT 

SERVICE POLICY AND PROCEDURE GUIDE 

ADDITIONAL WARRANTY EXCLUSIONS 

SHIPPING DAMAGE CLAIMS PROCEDURE 

1.     Resetting   of  safety  thermostats,  circuit breakers,  
 

overload protectors, or fuse replacements  unless       

 

warranted conditions are the cause. 

2.  All problems due to operation at voltages other than 
 

specified on equipment nameplates; conversion to 

 

 

 

 

 

correct voltage must be the customer’s responsibility. 

3.    All problems due to electrical connections not made in 
 

accordance  with  electrical  code  requirements  and  

 

wiring diagrams supplied with the equipment. 

4.     Replacement of items subject to normal wear, to include 
 

such items as knobs and light bulbs.  Normal maintenance 

 

functions including adjustment of thermostats, microswitches, 

 

and replacement of fuses and indicating lights are not 

 covered 

under 

warranty. 

5.     All problems due to inadequate water supply, such as 
 

fluctuating, or high or low water pressure. 

6.   All  problems  due  to  mineral/calcium  deposits,  or        
 

contamination from chlorides/chlorines. De-liming is 

 

 

 

considered a preventative maintenance function and is 

 

not covered by warranty. 

All 

electrical 

equipment 

manufactured 

by 

WELLS         

BLOOMFIELD, LLC is warranted against defects in materials 
and workmanship for a period of one year from the date of 
original installation or eighteen (18) months from the date of 
shipment from our factory, whichever comes first, and is for 
the benefit of the original purchaser, except that: 
a.     airpots carry a 30 day parts warranty only. 
b. 

dispensers; i.e., tea and coffee carry a 90  days parts      

        warranty only, excludes decanters. 

 
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN 
LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR 
IMPLIED,  INCLUDING  ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE, WHICH ARE HEREBY EXCLUDED.   
 
WELLS BLOOMFIELD, LLC SHALL NOT  BE  LIABLE  
FOR  INDIRECT,   INCIDENTAL  OR  CONSEQUENTIAL    
DAMAGES 

OR 

LOSSES 

FROM 

ANY 

CAUSE                

WHATSOEVER. 
 
This warranty is void if it is determined that upon inspection by 
an Authorized Service Agency that the equipment has been 
modified, misused, misapplied, improperly installed, or 

 

 

 

 

damaged in transit or by fire, flood or act of God. 

It also does not apply if the serial nameplate has been       
removed or unauthorized service personnel perform service.  
The prices charged by Bloomfield Industries for its products 
are based upon the limitations in this warranty.  Seller’s     
obligation under this warranty is limited to the repair of defects 
without charge by a Bloomfield Authorized Service Agency or 
one of its sub-agencies.  This service will be provided on   
customer’s premises for non-portable models.  Portable 

 

 

models (a device with a cord and plug) must be taken or 
shipped to the closest Authorized Service Agency, transporta-
tion charges prepaid, for services. 

 
In addition to restrictions contained in this warranty, specific 
limitations are shown below (Additional Warranty Exclusions).  
Bloomfield Industries Authorized Service Agencies are located 
in principal cities. 

 
This warranty is valid in the United States and void elsewhere.  
Please consult your classified telephone directory or your food 
service equipment dealer; or, for information and other details 
concerning warranty, write to: 

 

Service Parts Department 

Wells Bloomfield, LLC 

P.O. Box 280 

Verdi, NV  89439 

  Phone:  (775) 689-5707 

 

Fax: (775) 689-5976

 

  7.   Full use, care and maintenance instructions are supplied 
 

with each machine.  Those miscellaneous adjustments 

 

noted are customer responsibility.  Proper attention will 

 

prolong the life of the machine. 

  8.  Travel  mileage is limited to  sixty (60)  miles from an   
 

authorized Service Agency or one of its sub-agencies. 

  9.   All labor shall be performed during normal working hours.  
 

Overtime premium shall be charged to the customer. 

10.   All genuine Bloomfield replacement parts are warranted 
 

for ninety (90) days from date of purchase on non-

 

warranted equipment.  

Any use of non-genuine 

 

 

Bloomfield parts completely voids any warranty

11.  Installation, labor and job check-out are not considered 
 warranty. 
12.  Charges incurred by delays, waiting time or operating 
 

restrictions  that  hinder  the  service  technicians  ability  

 

to  perform services  are  not  covered  by  warranty.  

 

This  includes  institutional and correctional facilities. 

xi 

Summary of Contents for Integrity 9010



























Reviews: