manualshive.com logo in svg

Blonder tongue HDE-8C-QAM w/Opt 2, User Manual

Share
Download
Blonder tongue HDE-8C-QAM w/Opt 2 User Manual Download Page 12

12

HDE-8C-QAM 

Instruction Manual

Section 5 – Quick Start Guide

STEP 1 - Connect the Inputs

 

• Locate the blank receiver labels in the plastic bag supplied with the encoder.  

 

   Number each label with UNIT numbers 1 through 9.

 

• Find the receiver ID number label on the first receiver. Write the last 4 digits

 

   of the ID on  label #1 (RX1_####__) and place on the front of the receiver.

 

• Repeat for all 9 satellite receivers (8 primary plus 1 optional spare).

 

 

Now connect each receiver output to the encoder inputs, making sure that receiver #1 (RX#1)    

 

 

 

is connected to #1 component input on the encoder. Repeat this process for remaining receivers.

 

 

Connect the Receivers Control 10/100 port on the encoder (see section 2.2 #11 in manual) to    

 

 

 

an Ethernet switch (with a minimum of 5 ports) with a CAT 5 jumper cable.

 

 

Connect the 9 satellite receivers and the BBDECAs as shown below.

 

• Power up the receivers and the encoder.

1
2
3

CAT 5

Connect the equipment as follows:

RG-6

Refer to DirecTV

installation procedures

RX#1

A/V Cables

RX#8

Control & Monitoring

DT-16PT100M-RM

Receiver

Control

DT-05PT100M

PC w/web

browser

SWS-8WBMC

9501-M

Power Supply Port

BBDECA

SPARE

Ethernet Port

1

2

3

Summary of Contents for HDE-8C-QAM w/Opt 2













































Reviews:

No comments

Brands by name

Popular brands

Load more brands