Blomberg WNF 7301, User Manual

Page: 9 / 52

9 - EN
countdown:
1. Press the time delay button. Every time
the button is pressed, the time will be
increased in 1-hour increments.
2. If you wish to shorten the time delay, keep
on pressing the time delay button until the
time delay you would like to set appears on
the screen.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program:
1. Set the Time Delay to zero or turn the
Program selection knob to any program.
Thus, the time delay will be cancelled.
The “
” (End/Cancel) light flashes
continuously. Then, select the program you
wish to run again.
2. Press "Start/Pause" button to start the
program.
Starting the Program
1. Press "Start/Pause" button to start the
program.
2. Program follow-up lamp showing the
startup of the program will light up.
C
If no program is started or no key is
pressed within 1 minute during program
selection process, the machine will switch
to "Stand-by" mode and the illumination
level of the temperature, speed and door
indicators will decrease. Other lights and
indicators will turn off. In case of turning
the program selection knob or pressing any
button, lights and indicators will turn on.
Progress of program
Progress of a running program is shown
through the program follow-up indicator. At the
beginning of every program step, the relevant
indicator LED will light up and light of the
completed step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
program flow while the program is running.
However, the change to be made must be
compatible with the program step the machine
is currently in. If the change is not compatible,
relevant lights will flash for 3 times.
C
If the machine is not spinning, the
program may be in rinse hold mode or the
automatic spin correction system has been
activated due to an excessive unbalanced
distribution of laundry in the machine.
Changing the selections after the
program has started
Switching the machine to standby mode
Press the “Start/Pause” button to switch the
machine to pause mode while a program
is running. The light of the step which the
machine is in starts flashing in the program
follow-up indicator to show that the machine
has been switched to the pause mode.
Also, when the door is ready to be opened,
"Door" light will also illuminate continuously in
addition to the program step light. If necessary
conditions to open the door are not met, the
"Door" light will remain off.
Changing the speed and temperature
settings for auxiliary functions
Auxiliary functions can be cancelled or
selected, or the spin speed and temperature
settings can be changed in accordance with
the step the program is in. If the change can
not be made, relevant light will flash for 3
times.
Adding/removing laundry in pause mode
If the "Door" light flashes while the machine is
in pause mode, it means that the conditions
(low water level, etc.) to open the door have
been met and the period of approx. 1 or 2
minutes to open the door has started. “Door”
lamp will light up continuously when the door
is unlocked. Door can be opened to load or
unload the laundry after this moment. If the
front door cannot be opened because of a
safety reason after the machine has been
switched to the pause mode by pressing
the "Start/Pause" button, the "Door" light
will continue to remain off. Nevertheless, the
follow-up light of the relevant program in which
the machine was taken to "Pause" mode will
flash.
Door lock
The loading door can be opened once the
“Door” lamp stops flashing and starts lighting
up continuously.
Child-proof lock
Protect the appliance from being tampered
by children by means of the child-proof lock.
In this case, no change can be made in the
running program.
C
If the program selection knob is turned
when the child-proof lock is activated,
"Con" label will be displayed. In this
case, any change in temperature, speed
and auxiliary functions which are already
selected for the programs is not allowed.
C
If the program selection knob is turned
to "On/Off" position and then another
program is selected while a program is
running, the previously running program will
resume operating.
The machine is switched to child-lock by