Blomberg BRFB1920SS Installation Instructions Manual Download Page 36

Page: 36 / 118

CONFIDENTIAL

Preparing the Water Hose and the Power Plug

You will need a hose with a minimum length of 60" (1.5 meters) and a diameter of ¼" for water connections of the
product during installation. A connector that has a thread with an external diameter of ¼ must be used to connect
the

hose end to the product.



Connect the water hose to the mains, extend it and tape it to the ground.



The mains cable is provided externally with the product. First of all, connect the mains cable to the socket.



You can apply the method below to prevent the cable from getting jammed.

Use the Cable Clamp (29) and screw (30) to fix the cable connected to the socket to a level approximately
35" (890 mm) higher than the ground.

Summary of Contents for BRFB1920SS























































































































Search results

Summary of Contents for BRFB1920SS

Reviews:

Related manuals for BRFB1920SS

Brands by name

Popular brands

Blomberg BRFB1920SS, Installation Instructions Manual

Search results

Summary of Contents for BRFB1920SS

Reviews:

Related manuals for BRFB1920SS

Brands by name

Popular brands