background image

Complete the previous steps for the opposite side of the structure. 

 Add additional dabs of glue from the inside to ensure durability. 

6.  Ladder Assembly

Locate the ladder from etching D.   As with the other parts, be careful when 

cutting the part from the etching as you do not want to distort/bend it.   Note that the 
tabs extending from the ladder that allow it to mount onto the vertical posts should NOT 
be perpendicular to the bridge (they are at a slight angle for a reason).  

Locate the half-etched fold lines on the tabs extending from the bridge and bend 

them to form a right angle with the bridge.  If the ladder is perfectly vertical in your hand 
and you’re viewing it from the side, the tabs should angle up slightly.  When the ladder is 
mounted on to the bridge, the tabs will then become perfectly horizontal while the 
ladder will taper closer to the vertical posts as it rises up the structure.

Run a line of glue along 

dotted line (see arrow).

Repeat the same steps to

complete the opposite side.

Fold mounting tabs  perpendicular 

to the ladder.  These should NOT 

be perfectly perpendicular 

to the ladder.

Add a dab of glue to the ends of
each tab and place on model so 

the top, curled over handrails

are just above the walkway.

Make sure the ladder is firmly 

glued in place.  Bend the two 

curled runner tops inward 

as shown above.

We’ve included a typical Electrical Box to 

compliment  the  Signal  Bridge.    To  assemble, 
simply clean up the castings, glue the doors in 
place (line up the hinges for best results), and 
affix the cast footings.  Like the other cast metal 
parts  in  this  kit,  the  Electrical  Box  is 
manufactured in conjunction with Details West.

Electrical Box

Electrical Box

#4020 - Signal Bridge Instructions               Page 5

Summary of Contents for Cantilever Signal Bridge







Reviews: