background image

BLiss tuBs

save these instructions

10

© 2015 - 2017 Bliss Walk-in Bathtubs. All Rights Reserved.

2. Bath Drain & overflow Kit and Door Drain

The bath drain and overflow kit should be installed up to the final connection before the tub is installed (for 

reverse drain kit installation see Appendix C [page 30]). The drain shoe is most easily installed when the bathtub 

is standing on its end. When tipping the tub on its end make sure the fiberglass corner of the tub is well protected. 

Do not rotate the tub while it is standing on its end as this may damage the fiberglass corner and edge. Make 

sure that any moving parts (i.e. the door and door handle) are secure to avoid any unnecessary jarring of the 

components. Never lift the bathtub by any portion of the integrated plumbing or electrical systems.

• 

Install the drain shoe piece with the 1½” outlet facing towards the faucet side of the tub, as shown below. 

Two ferrule bolts are provided, one 1” long and one 1¼” long. The bolt used will depend on the thickness of 

the fiberglass drain hole. Only one is required.

• 

Apply a bead of silicone or plumber’s putty between the drain flange and the tub body.

• 

Screw the small ferrule bolt through the flange and into the drain shoe piece.

• 

Make sure the rubber gasket has not bulged out on the side. If it 

has, then loosen the ferrule bolt, adjust the gasket, and re-tighten. 

Apply a second even coating of silicone around the drain shoe 

connection on the underside of tub body to ensure a proper seal. 

Smooth with fingertip to close any gaps in the watertight seal.

• 

Install overflow portion of drain kit as shown to the right 

and silicone around the back side to prevent leaks.

• 

Ensure  the  overflow  knob  is  well  secured 

into the groove of the actuator shaft. A loose 

set screw can effect drain operation.

• 

The edges of the overflow wall fitting can be 

filed as needed to improve knob function.

• 

Use 1½” PVC pipe to connect the overflow 

outlet  to  the  sanitary  tee,  door  drain  tie-in, 

and  drain  shoe  as  shown  in  the  diagram 

below. If feasible, it is recommended to use a 

reducer and flexible PVC pipe (not provided) 

between  the  overflow  shoe  and  lower 

connections. This step will make any future 

maintenance of the faucet valves simpler.

• 

The  ⅜"  vinyl  tubing  coming  from  the  door 

drain  is  supplied  with  excess  length  and 

needs  to  be  cut  to  the  appropriate  length 

once the drain shoe is affixed to the tub. Cut 

the tubing so that there is a downward slope 

in the ⅜" tubing from the door drain fitting to 

the drain shoe. 

DO NOT cut off the integrated 

check valve!

instaLLation

iMPortant...

 

use APPRoPRIAte BondInG Glue. 

THE KITS SUPPLIED ARE PVC. ENSURE 

THAT IF SECURING TO AN EXISTING ABS DRAIN LINE, THE APPROPRIATE BONDING GLUE IS USED.

caution...

 

stoPPeR  set  sCReW  AdJustMent  Is  eXtReMelY  IMPoRtAnt  And  Is 

detAIled In tHe test PRoCeduRes on PAGe 19.

© copyright Bliss Tubs 2015 | © copyright Bliss Tubs 2015 | © copyright Bliss Tubs 2015

© c

op

yr

igh

t Bliss 

Tubs 2015 | © c

op

yr

igh

t Bliss 

Tubs 20

15

© c

op

yr

igh

t Bliss 

Tubs 2015 | 

© c

op

yr

igh

t Bliss 

Tubs 2015 | © c

op

yr

ig

ht Bliss 

Tubs 2015 | © c

op

yr

igh

t Bli

ss 

Tubs 2015 | © c

op

yr

igh

t Bliss 

Tubs 2015

© copyright Bliss Tubs 2015

Overflow

Knob

Overflow

Set Screw

1½” PVC Pipe*

Swivel Ball Joint

Stopper 

Actuator 

Cable

Tub 

Wall

Overflow 

Shoe

Stopper

Tub 

Floor

Large 

Ferrule 

Bolt

Overflow 

Wall

Fitting

Gasket

Door 

Drain**

Gasket

1½” PVC 

Drain 

Shoe

Drain

Flange

*PVC Pipe for plumbing 

connections is to be 

provided by installer

**Door Drain 

pre-installed on tub

1½” PVC Pipe*

Check 

Valve

1½” PVC Door 

Drain Tie-In

Adjustable 

Stopper Set 

Screw & Bolt

1½” Sanitary Tee

Tie-In to 

P-Trap*

Small 

Ferrule 

Bolt

O-ring

Actuator Shaft 

with Groove

Loctite™

Tape

Loctite™

Tape

⅜” tubing from door drain 

(to 

be connected by installer)

Shorten ⅜” tubing as 

needed to prevent 

sagging line

⅜” Barb Door 

Drain Tie-In

Summary of Contents for B3252HC









































Reviews: