YOU SHOULD HAVE
VALANCE CLIP
Hook the valance clips evenly along
the length of the headrail, prior to
installing the blind in the brackets.
HOLD DOWN BRACKET
Hold down brackets using two small
screws, screw hold down bracket to
window facing or wall.
Snap bracket pin ends into the hole at
bottom rail end.
(OPTIONAL)
X2
Engage the top leg of the valance
clip into the groove on the back of
the valance. Then push the valance
towards the headrail to engage the
bottom leg.
HOLD DOWN BRACKET
(OPTIONAL)
If your blind has been supplied with
valance returns slide the valance
return clip onto the valance. Slot the
other end of the valance clip onto the
valance return and align the edge.
FITTING THE HEADRAIL
ATTACHING THE VALANCE
INSTALLING CHILD SAFETY DEVICE
SAFETY DEVICE
Cord safety cleat
- The safety cleat
shall be installed as close to the
headrail as possible and in all cases not
less than 1500mm from the floor.
The Cord must be fully accumulated
around the safety cleat(s) when the
blind is not in use.
Use the table below to determine the
distance required between the cleats
to fully accumulate the cords when the
blind is fully raised.
Place the safety cleat in the desired
position on the wall and mark the
positions of the holes with a pencil.
(Note: Based on cord up to 2.8mm,
17m can be accumulated in total.)
(Note: Based on cord up to 2.8mm,
17m can be accumulated in total.)
* Distance
between
cord cleats
Use the screws provided to attach the
safety cleat to the wall..
X2
Wrap the cords around the cord cleats
in a figure of 8. When the cords are
fully accumulated ensure they are
secure so when any cord is pulled no
excess cord is released.
THE INSTALLATION HEIGHT OF THIS BLIND MUST NOT BE LESS THAN
1500MM FROM THE FLOOR.
FITTING THE BOX BRACKETS
OUTSIDE RECESS
If the blind is to be fitted outside
the window ensure that measure-
ment C is the same. Follow instruc-
tions for FACE FIXING. To calculate
C=(A-B)/2.
INSIDE RECESS
TOP FIX to the lintel or FACE FIX
brackets to the window frame.
(A) Width of Blind
(B) Top Fix
(C)
(C)
TOP FIXING
Measure & mark the distance
between the wall & the back of the
bracket, allowing for obstructions
like handles that protrude into the
recess area. The brackets should
be positioned 6mm wider than
the blind at each end. Hold each
bracket into place and mark the
hole positions. Fit each bracket
using the screws provided. Please
ensure fixings are suitable for the
wall/surface to which you are
mounting the brackets.
FACE FIXING
The brackets should be positioned
6mm wider than the blind at each end.
Hold each bracket into place and mark
the hole positions. Fit each bracket
using the screws provided. Please
ensure fixings are suitable for the wall/
surface to which you are mounting the
brackets
SIDE FIXING
CENTRE SUPPORT BRACKET
For larger width blinds a centre
support bracket is required.
Align the top of the centre support
bracket with the top of the mounting
bracket before installation.
Install with the bigger flap of the
centre support bracket on the top
equally spaced along the width of the
headrail and clear of the slat
ladder positions.
CHILDREN CAN STRANGLE IF A
SAFETY DEVICE IS NOT INSTALLED.
ALWAYS USE A SAFETY DEVICE TO
KEEP CORDS AND CHAINS OUT OF
REACH OF CHILDREN.
Hold each bracket into place and mark
the hole positions. Fit each bracket
using the screws provided. Please
ensure fixings are suitable for the wall/
surface to which you are mounting the
brackets.
TOOLS REQUIRED
• Screwdriver
• Pencil
• Power-Drill
• Tape Measure
BRACKETS
SAFETY DEVICE
WOOD SCREWS
(2 per bracket)
VALANCE & RETURN CLIPS
HOLD-DOWN BRACKET
(x2)
• 2 screws for safety cleat
• 4 small screws for hold down brackets
(2 per bracket)
Open the gate of the box brackets and
slide the headrail into position then
snap the brackets closed.
Number of
ladders
brackets
Centre support
brackets
(supplied)
0
1
1
2
3
3
4
2
3
4
5
6
7
8
9
2
2
2
2
2
2
2
2
4
Drop of Blind
*Distance between
cord cleats (centre
to centre)
1-1000mm
100mm
1001-2000mm
150mm
2001-3000mm
300mm
