manualshive.com logo in svg

BLEMO ER41, Manual

Share
Download
BLEMO ER41 Manual Download Page 72

Software Setup 

72 

ER41, ER24 

 

 

 

Functional Profiles Supported by the Drive

 

 

I/O Profile

 

 

Using the I/O profile simplifies PLC programming. 

The I/O profile mirrors the use of the terminal strip for control by utilizing 1 bit to control a function. 

The I/O profile for the drive can also be used when controlling via a fieldbus.The drive starts up as soon as 
the 

run 

command is sent.15 bits of the control word (bits 1...15) can be assigned to a specific function. 

This profile can be developed for simultaneous control of the drive via: 

  

The terminals 

 

The Modbus control word 

  

The CANopen control word 

 

Ethernet Modbus TCP embedded 

  

The fieldbus module control word 

The I/O profile is supported by the drive itself and therefore in turn by all the communication ports 
(integrated Modbus, CANopen, Ethernet, PROFIBUS DP, PROFINET, and DeviceNet fieldbus modules). 

 

CiA402 Profile

 

 

The drive only starts up following a command sequence. 

The control word is standardized. 

5 bits of the control word (bits 11...15) can be assigned to a function. 

The CiA402 profile is supported by the drive itself and therefore by all the communication ports (Modbus, 
CANopen, Ethernet, PROFIBUS DP, PROFINET, and DeviceNet). 

The drive supports the 

velocity 

mode of CiA402 profile. 

In the CiA402 profile, there are two modes that are specific to the drive and characterize commands and 
references value management: 

Separate 

[Separate] 

( 

) 

Not separate 

[Not separ.] 

( 

), 

Summary of Contents for ER41































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands