BLEMO ER41 Manual Download Page 65

Page: 65 / 126

Software Setup

ER41, ER24

Display

Monitoring Menu

The

Monitoring

menu contains the following items:

Drive Monitor

Data viewer/editor

Save and restore configuration

Drive Monitor Page

The figure shows the

Drive Monitor

page:

The state displayed in the

ER41 und ER24 Status

field corresponds to the display on the graphic

display terminal. A delay may be noticed between the displays on the Web server and the display
terminal. This delay depends on the performance of the computer used to display the pages using a web
browser and the communication system performance.

The motor speed displayed on the

Motor Speed (RPM)

gauge is calibrated according to the drive and

motor settings.

The LI... Gives the state of the drive terminal

DI1...DI6

DI11...DI16

: Logical inputs

R1...R6

: Relay outputs

AI1...AI5

: Analog inputs

DO11...DO12

: Analog/digital output

Green LED indicates that the logical input is active.

Red LED indicates that logical output is active

Summary of Contents for ER41































































































































Search results

Summary of Contents for ER41

Reviews:

Brands by name

Popular brands

BLEMO ER41, Manual

Search results

Summary of Contents for ER41

Reviews:

Brands by name

Popular brands