manualshive.com logo in svg

Blaze King KING KE1107, Owner'S Installation And Operation Manual, Page: 4 / 57

Share
Download
Blaze King KING KE1107 Owner'S Installation And Operation Manual Download Page 4

4

Date Printed: 4/28/11

File: G:/pubdata/Manuals\english manuals\OM-KE/PE.pub

OM KE/PE 1006

Version 1.11 Revised: DApril 2011

IF THIS BLAZE KING STOVE IS NOT PROPERLY INSTALLED OR OPERATED, A HOUSE FIRE MAY

RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. CONTACT LOCAL

BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION

REQUIREMENTS IN YOUR AREA.

THIS STOVE MUST BE CONNECTED TO EITHER:

1.

A LISTED FACTORY BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS AND CONFORMING TO, ULC629 IN
CANADA OR UL-103HT IN THE USA.

2.

A CODE-APPROVED MASONRY CHIMNEY WITH A FLUE LINER.

PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW ROOM HEATER. FAILURE

TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.

This unit is certified by the United States Environmental Protection Agency. Certified to comply with July, 1990
particulate emissions standards.

The following statement is required by the Environmental Protection Agency:

"This wood heater contains a catalytic combustor, which needs periodic inspection and replacement for

proper operation. It is against the law to operate this wood heater in a manner inconsistent with operating

instructions in this manual, or if the catalytic element is deactivated or removed."'

See pages 36&37 for Catalytic Combustor, Testing and Replacement.

SAVE THESE INSTRUCTIONS

Safety Warning

NOTE

Due to high efficiencies of these units, Blaze King recommends the
use of double wall stove pipe from the stove top to either wall or
roof exit.

No two installations are identical, specific performance and use will
vary with each application.

A minimum of 36” vertical rise is recommended prior to using any
elbows

.

Summary of Contents for KING KE1107


























































Reviews:

No comments