manualshive.com logo in svg

Blaze King KING KE1107, Owner'S Installation And Operation Manual, Page: 30 / 57

Share
Download
Blaze King KING KE1107 Owner'S Installation And Operation Manual Download Page 30

30

Date Printed: 4/28/11

File: G:/pubdata/Manuals\english manuals\OM-KE/PE.pub

OM KE/PE 1006

Version 1.11 Revised: DApril 2011

Optional Accessories

SIDE SHIELD KIT,

KE1107 (P/N S/SK1107)

SIDE SHIELD KIT,

PE1006 (P/N S/SP1006)

SIDE SHIELDS ARE STANDARD ON THE ULTRA MODEL

REQUIRED FOR:

MOBILE HOME, any installation

RESIDENTIAL REDUCED CLEARANCE
RESIDENTIAL ALCOVE

TOOLS NEEDED FOR INSTALLATION

1. Pliers, or wrench

INSTALLATION (both models)

1.

Place one of the Side Shields in place on the stove. (The shields will only fit on the sides for which they are
intended.) Slide the tab on shield top under the clip that is just under the top of the stove.

2.

Hold the shield tight on the side of the stove. Slide to front and to back until holes in bottom of side shield align with
holes in bottom of stove.

3.

Drop one bolt through each hole. Place nut on bottom of bolt and tighten.

4.

Install the other shield.

REAR SHIELD KIT, KE1107

(P/N R/S1107)

REAR SHIELD KIT,

PE1006 (P/N R/SP1006)

EITHER this Rear Shield OR the Fan Kit (P/N Z1714) is REQUIRED FOR:

MOBILE HOME, any installation
RESIDENTIAL ALCOVE
RESIDENTIAL CLOSE CLEARANCE

TOOLS NEEDED FOR INSTALLATION

1. Phillips or square drive screwdriver.

INSTALLATION (both models)

1.

The rear shield goes across the back of the stove, just below the thermostat knob. Place shield into position, insert
and tighten the two #10 X 1 1/4" screws provided.

Summary of Contents for KING KE1107


























































Reviews:

No comments