OPERATING INSTRUCTIONS
Adjustments Depth Of Cut At 90° (Fig.15 & 16)
•
The Circular Saw has an adjustable depth of cut. To adjust the depth of cut slacken the knob located on the side of the
machine (Fig.15).
•
Measure the depth required from the base plate to the highest point of the blade or use the depth gauge on the fixed guard.
Angle Of Cut 0-45° (Fig. 17)
•
Located at the front of the machine is the 0-45° locking knob (Fig.17). Slacken the lever and the base plate assembly will rotate
between 0-45°. Set the desired cutting angle by using degree scale at the front of the machine and tighten the locking lever.
•
At the front of the base plate there are two notches marked 90° and 45°. These notches are a guide to indicate the position of
the blade in relation to the cut being made in the material.
Parallel Cutting (Fig.6)
•
This machine is supplied with a parallel cutting guide. This cutting guide is fitted to the front of the machine and secured with
the locking knob.
Changing The Blade (Figs. 3-5)
•
Always ensure that the Circular Saw is disconnected from the battery before carrying out any maintenance or adjustments.
•
The blade is extremely sharp and care must be observed when handling.
•
Caution must be observed as the blade guard is spring loaded and if released may cause an injury. Rotate the blade guard into
the fully open position and secure it in this position using a screwdriver or piece of wood.
•
Depress the spindle lock (Fig. 3) and using the supplied hex key, unscrew the hex socket screw in an anti-clockwise direction.
(Fig 4)
•
Remove the hex socket screw and the retaining flange noting which way round the retaining flange is fitted. You can now
remove the blade.
•
Do not dispose of the blade in house-hold waste, recycle correctly.
•
Take note of the position of the inner flange, if this should fall off it must be replaced
•
Remove any wood debris from around the motor spindle and the two flanges.
•
Fit the new blade as shown in (Fig.5) ensuring that the direction of rotation arrow on the blade corresponds with the direction
of rotation arrow on the fixed guard. Replace the retaining flange and blade bolt.
•
Tighten the hex socket screw securely but do not over tighten.
•
Check the tightness of the hex socket screw before, during and after each use.
•
Remove the piece of wood or screwdriver that is holding it in the open position. Slowly release the guard so that it covers the
blade.
•
Check the operation of the blade guard making sure that it operates correctly. The operation is complete and your machine
is ready for use.
Product Specifications
Voltage
18V DC
No load speed
3800min-1
Max cut at 90º
54mm
Max cut at 45º
40mm
Blade size
Ø165 x Ø16mm
Sound Pressure Level
LpA 85 dB(A) K=3dB(A)
Sound Power Level
LWA 96 dB(A) K=3dB(A)
Vibration Level
5.33 m/s2, K=1.5m/s2
Summary of Contents for LGA 754012
