background image

blaubergventilatoren.de

CiViC eC d(1)B(e; e2)

18

The unit with a drain pump is intended for connection to power mains with parameters 1~230 V/50 Hz, without a drain pump — 1~230 

V/50(60) Hz. The drain pump is not included in the delivery set and must be purchased separately.

•  The unit must be connected to power mains using insulated electric conductors (cables, wires). The actual wire cross section selection 

must be based on the maximum load current, maximum conductor temperature depending on the wire type, insulation, length and 
installation method. .

•  The external power input must be equipped with an automatic circuit breaker built into the stationary wiring to open the electric circuit 

in case of overload or short-circuit.  The circuit breaker installation place must provide quick access for emergency shutdown of the unit.  
The trip current of the automatic circuit breaker must exceed the maximum current consumption of the unit (refer to the technical data 
table).  The recommended trip current of the circuit breaker is the next current in the standard trip current row following the maximum 
current of the connected unit.  The circuit breaker is not included in the delivery set. 

ADDITIONAL EXTERNAL CONTROL DEVICES CONNECTION 

To provide access to the place for connection of the units, it is necessary to 
remove the side decorative panel, which hides: 

Set Up Mode. 

Terminal block for connection of external control units according to the 

wiring diagram. 

2

1

External wiring diagram   

(CIVIC EC D(1)B S21; S22; S25)

C NC C NO C NO GND A B +24V

1 2 3 4 5 6 7 8 9

10

GND

В

+24V

A

1

F1

РE L1

L1

N

1

N

P1

*

3

1

4

CCU

*

1

2

Boost

*

PK1

*

X1

X2

5A

2

1

2

~230

 VAC

Power input

remove jumper

Designations 

Name

Cable type

Contact type

Note 

РК1*

Fire alarm panel

2x0.75 mm

2

NC

Remove the jumper

CCU*

Cooler control

2x0.75 mm

2

NO

3 A, ~250 AC

Р1*

External control panel

4x0.25 mm

2

Boost*

Contact ON/OFF, Boost mode

2x0.75 mm

2

NO

F1

Fuse 5A

5x20, slow

*Additionally connected devices are not included in the delivery set, purchased separately. 

CONNECTION TO POWER MAINS

POWER OFF THE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.

THE UNIT MUST BE CONNECTED TO POWER SUPPLY BY A QUALIFIED ELECTRICIAN.

THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE 

MANUFACTURER’S LABEL.

Summary of Contents for CIVIC EC D1B 300

























Reviews: