background image

The warranty is exclusively limited to the defects of workmanship.  
Any and all defects and malfunctions including mechanical damage caused by physical 
contact in the course of operation or natural wear and tear shall not be deemed warranty 
cases.  
The warranty liabilities shall not cover any malfunctions resulting from disregard of the 
instructions specific to the operation, care and maintenance of the unit or any 
unauthorised alterations and modifications to the unit design made by the user or any 
third party.  
Furthermore, the warranty shall not apply to any damage resulting from accidents, 
lightning strike, water, fire, war, public disorder or any other factors beyond the reasonable 
control of the manufacturer and its official distributors.  

RELATED DAMAGE LIABILITY WAIVER  

The manufacturer shall not be liable for any deterioration of health or damage to 
equipment caused by violating the provisions of the present User's Manual, unit misuse or 
gross mechanical tampering.  
The company does not provide compensation for any related damage (e.g. unit relocation 
and re-connection, direct or indirect damages etc.) related to the unit replacement.  
The manufacturer's warranty shall not cover any and all transportation expenses or any 
other expenses including the risks specific to unit deactivation, transportation and 
installation.  
The warranty for mounting, electrical equipment installation and adjustment work must 
be provided by the respective contractor.  
In any case the compensation under the present warranty may not exceed the amount 
actually paid for the faulty unit by the buyer.  

www.blaubergventilatoren.de

13

Box-D

Summary of Contents for 4058448013898

















Reviews: