background image

 

 

BladeZ Corporation  •  20155 Ellipse  •  Foothill Ranch  •  CA  •  92610 

www.ebladez.com

  •  Phone 949-206-8152  •  Fax 949-206-0013 

18

OPERATION CONTINUED 

 

Health Index Test Function 

 

NOTICE: This function can be used only after Run End is displayed in the matrix 
window. 
 
This function can calculate the health index based on the variance of heart rate in 
one minute after exercise. If the heart rate has no change in one minute, then the 
health index will be 6. If the heart rate recovers (decreases) more, then the index 
number will be smaller, that is to say you are healthier. 
 
Operation Method: In Run End mode, the matrix window displays Run End. First, 
make sure that the heart rate signal blinks and the heart rate number is displayed 
by gripping the pulse rate sensors on either side of the console. Then press 
PULSE Recovery key. After you press the PULSE Recovery key, the matrix 
window will display ”Rec” and then count down for one minute. If there is no heart 
rate signal input, the matrix will display ”Rec” and “Error” to show that the test 
fails. If the test succeeds, after one minute the Work Level window will display the 
initial tested heart rate number, the RPM window will display the last tested heart 
rate number, then the Distance window will display the variance between the 
above two numbers. The matrix window will display ” Rec ” and the health index 
and then come back to the Start/Ready status after several seconds. 
 
 

Temperature Function  

 

NOTICE: This function can be used only under Start/Ready mode. 
 
Operation Method: Under Start/Ready status, if you press PULSE Recovery key, 

the RPM window will display the room temperature, and display °F for 
Fahrenheit unit, °C for Celsius unit. After 5 seconds, it will come back 
to the Start/Ready display. 

Summary of Contents for ION 490E





















Reviews: