Program Change Assignment
To change the default assignments and set the amp up to respond to a different set
of Program Changes:
1. The amp must be powered on with either the Standby switch (23) set to on, a
jack in the Input socket, or both.
2. Send the appropriate Program Change message to the amp.
3. Press and hold in the appropriate front panel Channel Select switch for 2
seconds.
The corresponding channel will be selected and its LED will flash three times in quick
succession to indicate it has been assigned to the last received Program Change.
The amplifier will now remember the selection. Repeat the operation until all your
Program Changes have the desired amp channel assigned to them.
MIDI Receive Channel Selection
As mentioned previously, the default mode is set to OMNI and the amplifier will
respond to MIDI Program Changes on all MIDI channels. You may wish to set the
amplifier to respond to Program Changes on just a single MIDI channel. The Series
One can be set to respond in this way for any of the first seven MIDI channels as
follows:
1. The unit must be in standby (Power (24) on and Standby (23) off), and no lead
connected to the Input jack.
2. Simultaneously press and hold the Bright Clean (3) and Crunch (9) Select
switches.
3. After 2 seconds the LED for Super Crunch (10) will begin to flash continuously
(2 flashes per second) to indicate that the unit is in MIDI Receive Channel
Program Mode.
4. Release the Bright Clean (3) and Crunch (9) Select switches and select the
required MIDI channel by using the Channel Select switches as shown in the
table below:
The corresponding Channel Select LEDs will illuminate to show the selection and
each press of the Channel Select switches will toggle the state of its associated
LED.
English
13
22. Power Indictior Light
The power indicator will light when the amplifier is switched on.
23. Standby
This switch applies the H.T. (High Tension) voltage required to produce sound to the
output stage. Always turn this switch on at least 30 seconds after the Power switch
(24). During short breaks in playing use just this switch to turn ‘off’ and ‘on’ the
amplifier’s output.
24. Power
This switch is used to turn the amplifier on and off. You should always turn this switch
on before turning on the Standby switch (23).
MIDI Channel Switching
The Series One offers the ability to control channel selection via MIDI Program
Change messages and interfacing with most MIDI controllers is a straight forward
process. The Series One can be placed in a MIDI chain allowing you to
simultaneously select a channel on the amplifier and change the patch on a MIDI
effects processor connected to the effects loop. There are 128 available Program
Changes, giving you the possibility to access a vast number of tonal combinations.
To set-up MIDI channel switching, simply connect the MIDI controller’s MIDI Out
socket to the MIDI In socket on the rear of the amplifier. The controller should be set
to transmit Program Change messages (this is usually the case). From new, a Series
One amplifier is set to OMNI mode and responds to Program Change messages on
all MIDI channels. Changing ‘patches’ on the controller will change the selected
channel on the amp. The default settings for each Program Change number are
shown in the table below:
English
12
Program Channel
Change
1
BRIGHT CLEAN
2
WARM CLEAN
3
CRUNCH
4
SUPER CRUNCH
5
BRIGHT CLEAN
6
WARM CLEAN
7
CRUNCH
8
SUPER CRUNCH
9
BRIGHT CLEAN
10
WARM CLEAN
11
CRUNCH
12
SUPER CRUNCH
13
BRIGHT CLEAN
14
WARM CLEAN
15
CRUNCH
16
SUPER CRUNCH
17
BRIGHT CLEAN
18
WARM CLEAN
19
CRUNCH
20
SUPER CRUNCH
21
BRIGHT CLEAN
22
WARM CLEAN
23
CRUNCH
24
SUPER CRUNCH
25
BRIGHT CLEAN
26
WARM CLEAN
27
CRUNCH
28
SUPER CRUNCH
29
BRIGHT CLEAN
30
WARM CLEAN
31
CRUNCH
32
SUPER CRUNCH
33
BRIGHT CLEAN
34
WARM CLEAN
35
CRUNCH
36
SUPER CRUNCH
37
BRIGHT CLEAN
38
WARM CLEAN
39
CRUNCH
40
SUPER CRUNCH
41
BRIGHT CLEAN
42
WARM CLEAN
43
CRUNCH
44
SUPER CRUNCH
45
BRIGHT CLEAN
46
WARM CLEAN
47
CRUNCH
48
SUPER CRUNCH
49
BRIGHT CLEAN
50
WARM CLEAN
51
CRUNCH
52
SUPER CRUNCH
53
BRIGHT CLEAN
54
WARM CLEAN
55
CRUNCH
56
SUPER CRUNCH
57
BRIGHT CLEAN
58
WARM CLEAN
59
CRUNCH
60
SUPER CRUNCH
61
BRIGHT CLEAN
62
WARM CLEAN
63
CRUNCH
64
SUPER CRUNCH
65
BRIGHT CLEAN
66
WARM CLEAN
67
CRUNCH
68
SUPER CRUNCH
69
BRIGHT CLEAN
70
WARM CLEAN
71
CRUNCH
72
SUPER CRUNCH
73
BRIGHT CLEAN
74
WARM CLEAN
75
CRUNCH
76
SUPER CRUNCH
77
BRIGHT CLEAN
78
WARM CLEAN
79
CRUNCH
80
SUPER CRUNCH
81
BRIGHT CLEAN
82
WARM CLEAN
83
CRUNCH
84
SUPER CRUNCH
85
BRIGHT CLEAN
86
WARM CLEAN
87
CRUNCH
88
SUPER CRUNCH
89
BRIGHT CLEAN
90
WARM CLEAN
91
CRUNCH
92
SUPER CRUNCH
93
BRIGHT CLEAN
94
WARM CLEAN
95
CRUNCH
96
SUPER CRUNCH
97
BRIGHT CLEAN
98
WARM CLEAN
99
CRUNCH
100
SUPER CRUNCH
101
BRIGHT CLEAN
102
WARM CLEAN
103
CRUNCH
104
SUPER CRUNCH
105
BRIGHT CLEAN
106
WARM CLEAN
107
CRUNCH
108
SUPER CRUNCH
109
BRIGHT CLEAN
110
WARM CLEAN
111
CRUNCH
112
SUPER CRUNCH
113
BRIGHT CLEAN
114
WARM CLEAN
115
CRUNCH
116
SUPER CRUNCH
117
BRIGHT CLEAN
118
WARM CLEAN
119
CRUNCH
120
SUPER CRUNCH
121
BRIGHT CLEAN
122
WARM CLEAN
123
CRUNCH
124
SUPER CRUNCH
125
BRIGHT CLEAN
126
WARM CLEAN
127
CRUNCH
128
SUPER CRUNCH
Bright Clean
Warm Clean
Crunch
MIDI CHANNEL
OFF
OFF
OFF
OMNI
ON
OFF
OFF
1
OFF
ON
OFF
2
ON
ON
OFF
3
OFF
OFF
ON
4
ON
OFF
ON
5
OFF
ON
ON
6
ON
ON
ON
7
