Black BLK-CDS105NH Instruction Manual Download Page 17

1. LENS                              DC

2. EXPOSURE

3. WHITE BAL                 ATW

4. BACKLIGHT                OFF

5. DNR                               ON

6. DAY/NIGHT                 AUTO

7. IMAGE ADJ

8. SPECIAL

9. EXIT

MAIN SETUP

3. Set the DNR mode to ‘ON’ and press the SET button. Then you can adjust 
     the noise reduction level.

You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using
    the Up and Down buttons so that the arrow indicates DAY/NIGHT .

 How to Use the Camera

2. Select a desired mode using the Left and Right buttons according to 
    the picture display you want.

COLOR : The picture is always displayed in color.

B/W : The picture is always displayed in black and white.

AUTO : The mode is switched to Color in a normal environment, 

                      but switches to B/W mode when ambient illumination is low. 
                      To set up the sswitching time or speed for AUTO mode, 
                      press the SET button.

Note

• When using a Video Auto Iris Lens, if you set the lens level to low, 
  automatic switching between Color and Black & White may not occur.
• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE 
   menu is ‘OFF’.
   At this time, the exchange between DAY mode and NIGHT mode 
   operates as like selecting ‘COLOR’ mode.
• The OSD key does not work for 3 seconds when switching to Color 
  or B/W, to ensure stable camera operation.
• The camera may focus less well under infrared illumination than under 
   normal illumination.
• Since the camera may not focus as well under infrared illumination 
   at night as it does under normal illumination, install an Extra-low 
   Dispersion Lens to obtain sharp pictures.

Note

• You cannot set the DNR to ‘ON’ or ‘OFF’ when the AGC mode of the 
   EXPOSURE menu is ‘OFF’.
• When adjusting the noise reduction level of the DNR mode, remember 
   that the higher the level set, the more the noise level will be reduced 
   but that after image may also occur.

DAY/NIGHT

EXTERN: This mode allows you to apply a desired filter to external signals.

30

31

Super DNR High Resolution Day/Night Camera

Super DNR High Resolution Day/Night Camera

Summary of Contents for BLK-CDS105NH
























Reviews: