background image

3-Pin Red Connector:

Plug-in connector port

for optional features harness.

• GREEN/BLACK WIRE - 3rd channel output (-).
Connect to a relay for optional trunk release etc.

• RED WIRE - Factory Disarm output (-).
Connect to the wire that requires a ground
pulse to disarm the factory alarm system. The
RED wire provides a ground pulse when the
remote transmitter is used to unlock the doors
or start the vehicle.

• YELLOW WIRE - Vacuum Switch input. For
diesel vehicles, or vehicles where a tach wire or
spark plug wire is not available, the YELLOW
wire may be connected to an optional vacuum
switch. Connect the other side of the vacuum
switch to ground.

2-Pin Red Connector:

Plug-in connector port

for LED. Mount LED in an area where it may be
easily seen from either side of the vehicle.

2-Pin Blue Connector:

Plug-in connector port

for program/service switch.

Mount program

switch in an area that is easily accessible from the
driver’s position.

2-Pin White Connector:

Plug-in connector port

for horn honk/dome light harness.
• WHITE/YELLOW - horn output (-)
• RED/BLACK - Dome light output (-)

5-Pin Antenna Connector:

Plug-in connector

port for extended range receiver. Plug harness
into 5-pin connector, route cable up pillar post,
place double sided tape on flat side of receiver
module and place in corner of windshield.

4

Remote Programmable Features:

Step

Function

Button 1 (On)

Button 2 (Off)

1.

Arming Mode

Passive

Active

2.

Passive Lock

On

Off

3.

Auto Re-arm 

On

Off

4.

Normal/Silent Arming

Normal

Silent

5.

Door Unlock Pulse

Single

Double

6.

Door Lock Pulse Length

.75 Seconds

3 Seconds

7.

Ignition Lock

On

Off

8.

Auto Cold Start Defeat

Disable Cold Start

Enable Cold Start

9.

Cold Start Timing

Every 2 Hours

Every 1 Hour

10.

Trunk Disarm Feature

Disable

Enable

11.

Passive Arm Warning Chirps Delete

On

Off

12.

Open Zone Chirp Timing

10 Seconds

60 Seconds

13.

Remote Start Run Time

15 Minutes

25 Minutes

14.

Lock Before & After Engine Crank

On

Off

15.

Lock After Engine Shutdown

On

Off

16.

Parking Light Operation

Normal

Car Locator Feature

Summary of Contents for 250













Reviews: